OEM Powermate Generator Parts & Accessories

Wheel

$64.15

Fix Number: FIX11873318
Manufacturer Part Number: 0L2261

Replace a damaged wheel with this 12 x 2.00 six-spoke design for portable equipment. Built from strong plastic with a black finish, it ensures smooth movement and stability. Easy to install for hassle-free mobility.

Isolator

$9.29

Fix Number: FIX11871112
Manufacturer Part Number: 0051094SRV

This is an Authentic replacement part designed for use with Powermate Generators. This part is made out of Rubber with a Metal Threaded Shaft in the middle. Includes 1 isolator per order. This part helps to secure Engine/Motor to the Frame. Because its made out of Rubber it helps to significantly reduce vibration from a running engine.

Fuel Shut Off- Inline

$11.66

Fix Number: FIX11873314
Manufacturer Part Number: 0L0813

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Powermate generators. The purpose of this component is to allow a user to shut off the fuel supply to the unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality fuel shut off valve is made of durable plastic and is sold individually.

Fuel Filter

$8.62

Fix Number: FIX11873316
Manufacturer Part Number: 0L1101

This fuel filter is a genuine OEM replacement part sourced directly from the manufacturer. It is customarily used in Powermate generators. This fuel filter removes rust and dirt particles from the gasoline moving through the fuel line. It is made of plastic and sold individually. It should be replaced if it broken or damaged. A screwdriver is needed to replace this part.

Fuel Shut-Off

$20.12

Fix Number: FIX11872493
Manufacturer Part Number: 0068565SRV

Wheel

$94.74

Fix Number: FIX11871959
Manufacturer Part Number: 0063771SRV

Foam Filled

Bridge Rectifier Board Assembl

$86.37

Fix Number: FIX11871920
Manufacturer Part Number: 0063525SRV

Designed for use with Powermate generators, this is an OEM approved replacement part for various models. For full compatibility, please see the "Model Cross Reference List" below. The primary purpose of the Bridge Rectifier Board is to lead and rectify the voltage from the transformer to the rotor. If your generator will turn on but will not produce power, you may need to replace your Bridge Rectifier Board. NOTE: The board will only work with the Jumper Kit (Part #S0064066). This part has dimensions of approximately 4"x3", and is sold individually.

Rubber Foot

$6.51

★★★★★

1 Review

Fix Number: FIX11870924
Manufacturer Part Number: 0047774SRV

This is a single OEM black rubber foot for a generator. The rubber foot is used to keep the unit secure on the ground while it is operating. It also keeps the frame off the floor to prevent it from damaging the unit or the floor itself. If your generator is unstable or the rubber foot has completely worn to the point that the unit comes in contact with the ground, its time to get it replaced.

Circuit Breaker (25 Amp)

$36.28

Fix Number: FIX11870960
Manufacturer Part Number: 0049072SRV

This replacement 25 amp circuit breaker is specially designed for use with Powermate generators. It is an authentic OEM sourced part, not an aftermarket imitation. This circuit breaker is an automatically operated electrical switch that will protect the unit from the damage caused by an overload or a short circuit. Its basic function is to detect a fault condition and interrupt current flow. Please note, this plastic item is sold individually. To replace this item you will need a screwdriver.

Isolator

$6.51

Fix Number: FIX11872556
Manufacturer Part Number: 0069338SRV

It is an authentic Powermate component which is specially designed for gas-powered generators. This is an identical replacement for a damaged or a missing isolator that was installed on a new unit. It helps to provide support and reduce vibrations from a working engine. This high-quality isolator is made of durable metal with rubber and is sold as an individual item. Check the diagrams for your model to ensure the correct repair procedure. A wrench will be needed to replace this isolator.

Installation Instructions

Stephen from HOWARD, KS

Generator was not powering anything

Removed rectifier cover on generator. Remove old rectifier. Had to use 1 1/4" hole saw to fit new rectifer board under rectifier cov er. Capacitor on new board is taller then original board. Re assemble in reverse order Read more...

Powermate Generator Parts

Popular Powermate Generator Parts

Installation Instructions

Powermate Generator Appliance Types

Related Powermate Generator Parts

Popular Powermate Generator Models

Powermate Generator Parts

Start With Your Model Number

Popular Powermate Generator Parts

Installation Instructions

Powermate Generator Appliance Types

Related Powermate Generator Parts

Popular Powermate Generator Models