OEM Black and Decker Workbench Parts & Accessories

Foot Boot

$6.51

Fix Number: FIX9927396
Manufacturer Part Number: 242393-00

This is a black OEM foot boot that is sold individually, however every workmate has four (one on each leg). This is a good opportunity to inspect all four foot boots in case you need to order multiple. The foot boot is what keeps the unit balanced and prevents it damaging the surface on which it is placed.

Watch the install video

Crank Arm

$6.51

Fix Number: FIX9927367
Manufacturer Part Number: 242302-00

This is a crank arm for a workmate, sold individually. It is also sometimes referred to as a handle arm. The hole that connects the crank to the shaft has a diameter of a 1/2-inch. The purpose of the crank arm is to open and close the front rear vise jaws. To assemble, place the crank arm over the vise screw rod end, line up the holes and secure the roll pin using a hammer.

Installation Instructions

Shawn from LOS GATOS, CA

A broken crank arm and knob had been replaced by one of dad's "creative" solutions (a pipe fitting & a rusty nail bent at a 90 degree angle). Yikes!

It would have been super easy if I had just had to follow your repair video. However, I had to punch out the metal pin, which went thru dad's make-shift repair (the pipe fitting) It was a bit stubborn. After that, I put the crank arm on & snapped the new knob on. If users follow your repair video, it should be very easy. Read more...

Slide Index Bracket

$9.96

Fix Number: FIX9927655
Manufacturer Part Number: 243024-00

This is a Genuine OEM Sourced replacement part designed for use with Workbenches. This item acts as a Support for Vise Jaws. It is made out of Plastic and it is Sold Individually. To replace it you would need a Wrench to remove and secure the Bolts that hold Slide Index and the Vise Jaws.

Grip

$6.51

★★★★★

1 Review

Fix Number: FIX10016520
Manufacturer Part Number: 807530-02

This is a genuine replacement grip that is sold individually. The grip is used on a workmate to secure work pieces on top of the jaws. The grip fits into the holes in the vise jaws and can be rotated to hold awkwardly shaped pieces. Due to its plastic material, it can become brittle, causing the locking tabs or shaft to break. Repairs do not get much easier than this. The grip can be placed in any of the holes on your work mate. Each grip has two locking tabs which will need to be aligned with the tabs on the hole in the workmate and then pressed into place.

Installation Instructions

Kevin from NEWBURGH, IN

The part was not made for the model I own.

Had to drill and tap for new threads Read more...

Pivot Nut

$6.51

★★★★★

1 Review

Fix Number: FIX10177708
Manufacturer Part Number: 5140047-14

This is an Authentic OEM sourced replacement part designed for use with Black and Decker Workmate. This item helps to secure the Vise Screw. This Pivot Nut is made out of Plastic and it is Sold Individually. To replace it you would need a Wrench.

Knob

$9.51

★★★★★

5 Reviews

Fix Number: FIX9927412
Manufacturer Part Number: 242440-00

This part includes one genuinely sourced plastic knob for a workmate. The knob attaches to the crank handle and is used to turn the crank vise to open or close the vise jaws. For this simple, tool-free repair, just snap the knob into place.

Installation Instructions

MATTHEW E from Prescott, AZ

Knob broke accidental tip over

Knob for old workbench was a different size but this wasn’t obvious. I tried to hammer in the “snap in” knob and broke the handle. Gorilla glue fixed that and all is well. Now, why did they change the size of the workmate knobs? Who knows. Read more...

Foot

$6.51

Fix Number: FIX9927397
Manufacturer Part Number: 242394-00

This is a single OEM foot for a workmate. Your unit will have four of these in total, so it is recommended to inspect all four feet and order the appropriate amount you need. The foot is what keeps the unit stable and level, so if one of more are damaged or missing this can make the workmate unbalanced.

Bag,hardware

$28.71

★★★★★

3 Reviews

Fix Number: FIX10167377
Manufacturer Part Number: 242829-03

This is the special hardware bag with swivel grip pegs which includes the components used on Dewalt and Black and Decker workmate benches. These are high-quality items that are made of durable plastic, please note this hardware bag is sold individually. Over time due to heavy use some plastic components may wear out or even break eventually requiring replacement.

Leg Catch

$10.34

Fix Number: FIX9927406
Manufacturer Part Number: 242416-00

This is a single OEM leg catch for workbenches. This part holds the leg on the workbench in the down position and locks it into the correct position. When it is released, the leg can raise back into the up position. If the legs of your workbench are wobbly or will not lock in place properly, a damaged leg catch is the likely culprit.

Installation Instructions

Roger from LIVONIA, MI

Replace broken leg catch

Punched out rod holding broken catch. Took it to bench grinder to taper ends when putting it back together after placing new leg catch on it. Tapering made it much easier on reinstall. Read more...

Block,slide Mov

$6.51

Fix Number: FIX10167357
Manufacturer Part Number: 242436-02

This item has been sourced from the original manufacturer to be used with work benches from Black and Decker. The slide block attaches to the bottom of the table and is used to allow the table to move across the rails. This item is sold as an individual replacement part.

Black and Decker Workbench Parts

Popular Black and Decker Workbench Parts

Installation Instructions

Installation Instructions

Installation Instructions

Installation Instructions

Black and Decker Workbench Appliance Types

Popular Black and Decker Workbench Models

Black and Decker Workbench Parts

Start With Your Model Number

Popular Black and Decker Workbench Parts

Installation Instructions

Installation Instructions

Installation Instructions

Installation Instructions

Black and Decker Workbench Appliance Types

Popular Black and Decker Workbench Models