OEM Ridgid Tool Stand & Cart Parts | Expert DIY Repair Help & Fast Shipping | Fix.com

Popular Ridgid Tool Stand & Cart Parts

$7.82
Height Adjust Lock Lever
Fix Number FIX10089720
Manufacturer Part Number 000999130700
This is a genuine OEM replacement part that has been sourced directly from Rigid. This height adjust lock lever assembly attaches to the lower tube assembly of your work support. Having one of these supports is handy in any work area, but due to wear in tear the plastic lever may break or become damaged. The height adjust lock lever secures the position of the support, whether it is set up and you are working, or whether it is folded flat and being stored you will need your lever in working order. The height adjust lock lever is sold individually.
Fixes these symptoms
No Symptoms for this part
$93.10
Vise Jaw
Fix Number FIX10096834
Manufacturer Part Number 41020
This is an authentic OEM replacement part that has been sourced directly from Rigid. This vise jaw is made of metal, and it is commonly used on chain vises. Chain vises are a type of pipe vise, used for bending pipe and conduit. The vise jaw is sold individually, and the hardware required for installation is sold separately.
Fixes these symptoms
No Symptoms for this part
$13.33
E-1444-X Chain Assembly
Fix Number FIX10096812
Manufacturer Part Number 40945
Fixes these symptoms
No Symptoms for this part
$7.91
Wear Plate
Fix Number FIX10104128
Manufacturer Part Number 93537
This is an authentic OEM replacement part that has been sourced directly from Rigid. Wear plates are used to lengthen the life of equipment that has components that slide together. In this case the wear plate is mounted underneath the wok surface where the jaws are mounted. This plate helps reduce wear to the equipment from abrasion, this helps limit the damage the chain may cause to the equipment. The plate is made of steel, and it comes with the jaw screws and washers.
Fixes these symptoms
No Symptoms for this part
$10.02
F-532 Grommet (5)
(1)
Fix Number FIX10096810
Manufacturer Part Number 40940
This is a genuine OEM replacement part that has been sourced directly from Rigid. These grommets, also known as rubber feet, are commonly used on pipe tools, and tool stands. Grommets help keep your equipment in one place, they also help keep it balances, and they help reduce vibration during operation. To install this replacement part you simply push the grommet into the pre-drilled hole and the bottom of your equipment. These rubber feet come in a pack of five.
Fixes these symptoms
No Symptoms for this part
$2.03
Rubber Foot
Fix Number FIX11864875
Manufacturer Part Number 000999130008
Fixes these symptoms
No Symptoms for this part
$6.38
Rubber Tip
Fix Number FIX10096394
Manufacturer Part Number 37962
This is an authentic OEM replacement part that has been sourced directly from Rigid. This rubber tip fits snuggly on the end of metal piping found on the frame of many common pieces of equipment. Most often this replacement part is used on tool stands, water jetters, drain cleaners, and drum machines. If a rubber tip wears down, becomes damaged, or is lost it will need to be replaced. This replacement part is sold individually.
Fixes these symptoms
No Symptoms for this part
$59.23
Handle, W/Nut BC410
Fix Number FIX10096842
Manufacturer Part Number 41050
This is a genuine OEM replacement part that has been sourced directly from Rigid. This handle assembly is most commonly used with chain vises. The assembly comes with the handle, the nut, and the friction ring. This handle attaches to the chain, however this assembly does not come with the chain screw. When you crank the handle the chain tightens around the pipe and holds it in place while you are working. The durable handle and nut are both made of metal.
Fixes these symptoms
No Symptoms for this part
$25.30
Handle For Chain Vise
Fix Number FIX10096831
Manufacturer Part Number 41015
Fixes these symptoms
No Symptoms for this part
$2.99
CLAMP LOCK LEVER
Fix Number FIX10089717
Manufacturer Part Number 000999130007
This is an authentic OEM replacement part that has been sourced directly from Rigid. This lock lever clamp is part of the height adjustment assembly. It is found between the lock lever and the lower tube assembly. It attaches the height adjust lock lever to the work support. The clamp has approximate dimensions of 1-inch x 1-inch X 1-inch, there is a bolt hole in the middle that has a diameter of 3/8 of an inch. This lock lever clamp is made of metal, and it is sold individually.
Fixes these symptoms
No Symptoms for this part

Popular Ridgid Tool Stand & Cart Models