Black and Decker Sawhorse Parts

Black and Decker Appliance Parts
Shop By Appliance Type

Popular Black and Decker Sawhorse Parts

$6.03
  In Stock
Leg Catch
Fix Number FIX9927406
Manufacturer Part Number 242416-00
This is a single OEM leg catch for workbenches. This part holds the leg on the workbench in the down position and locks it into the correct position. When it is released, the leg can raise back into the up position. If the legs of your workbench are wobbly or will not lock in place properly, a damaged leg catch is the likely culprit.
$3.08
  In Stock
Grip
★★★★★
★★★★★
(1)
Fix Number FIX10016520
Manufacturer Part Number 807530-02
This is a genuine replacement grip that is sold individually. The grip is used on a workmate to secure work pieces on top of the jaws. The grip fits into the holes in the vise jaws and can be rotated to hold awkwardly shaped pieces. Due to its plastic material, it can become brittle, causing the locking tabs or shaft to break. Repairs do not get much easier than this. The grip can be placed in any of the holes on your work mate. Each grip has two locking tabs which will need to be aligned with the tabs on the hole in the workmate and then pressed into place.
Installation Instructions
Kevin from NEWBURGH, IN
The part was not made for the model I own.
Had to drill and tap for new threads Read more...
$3.08
  In Stock
Boot,Foot
★★★★★
★★★★★
(1)
Fix Number FIX9927396
Manufacturer Part Number 242393-00
This is a black OEM foot boot that is sold individually, however every workmate has four (one on each leg). This is a good opportunity to inspect all four foot boots in case you need to order multiple. The foot boot is what keeps the unit balanced and prevents it damaging the surface on which it is placed.
$3.08
  In Stock
Foot
Fix Number FIX9927397
Manufacturer Part Number 242394-00
This is a single OEM foot for a workmate. Your unit will have four of these in total, so it is recommended to inspect all four feet and order the appropriate amount you need. The foot is what keeps the unit stable and level, so if one of more are damaged or missing this can make the workmate unbalanced.
$3.08
  In Stock
Arm,Crank
Fix Number FIX9927367
Manufacturer Part Number 242302-00
This is a crank arm for a workmate, sold individually. It is also sometimes referred to as a handle arm. The hole that connects the crank to the shaft has a diameter of a 1/2-inch. The purpose of the crank arm is to open and close the front rear vise jaws. To assemble, place the crank arm over the vise screw rod end, line up the holes and secure the roll pin using a hammer.
$5.52
  In Stock
Snap-In Knob
★★★★★
★★★★★
(1)
Fix Number FIX9927412
Manufacturer Part Number 242440-00
This part includes one genuinely sourced plastic knob for a workmate. The knob attaches to the crank handle and is used to turn the crank vise to open or close the vise jaws. For this simple, tool-free repair, just snap the knob into place.
$5.80
  On Order
Slide Index BKT
Fix Number FIX9927655
Manufacturer Part Number 243024-00
$3.08
  In Stock
Roll Pin
Fix Number FIX9927368
Manufacturer Part Number 242311-00
$3.08
  In Stock
Bolt
Fix Number FIX10036859
Manufacturer Part Number 98025-40
$29.06
  On Order
Vise Jaws (Dimensions: 24"L X 4 7/8"W) 1 Set of 2
★★★★★
★★★★★
(3)
Fix Number FIX10176022
Manufacturer Part Number 5140006-25
Installation Instructions
Steve from NEWPORT, NC
Old vice jaws needed replacing
Parts not available for 200 so ordered part for 225. Need to cut 1/4 inch off of vice jaws around the turn radius of the knobs. Other than that everything lines up fine Read more...

Appliance Type

Popular Black and Decker Sawhorse Models