OEM Porter Cable Impact Driver Parts & Accessories

Compression Spring

$6.51

Fix Number: FIX11929265
Manufacturer Part Number: N019351

The compression spring is part of the impact drivers chuck assembly. The spring is found over the anvil shaft and provides tension to pull the chuck collar back after a bit is removed. Over time this part can lose tension or become damaged. A failed compression spring will cause the collar to move freely, and the driver bit will come loose. This is an OEM official part and is sold individually.

Steel Ball

$6.51

Fix Number: FIX11929439
Manufacturer Part Number: N089668

The steel ball is part of the bit holder in an impact driver and is sold individually. The driver bit is held securely by the ball, which fits into the spindle. The ball is attached to the spindle by the collar. Over time, the collar can come loose, and the ball could get lost. The ball itself can sometimes wear, causing the driver to become loose rather easily. To access this part, you will need to remove the hog ring, which fits into a groove on the anvil. When removing this part, be careful not to misplace parts, as there is a spring behind the hog ring, which will become loose. This will allow you to remove the collar and steel ball. Remove the ball using a magnet, to keep it contained.

Ring,spring

$6.51

Fix Number: FIX11924891
Manufacturer Part Number: 086947-00

It is a genuine item that is supplied by the original equipment manufacturer for use with DeWALT, Black and Decker and Porter Cable impact wrenches. This is the special ring spring that is secured on the anvil, unfortunately, over time it will wear out, it may get damaged or lost eventually requiring a replacement. Make sure to check the diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

O-ring

$6.51

Fix Number: FIX11929412
Manufacturer Part Number: N075339

O-rings are commonly utilized to provide a tight seal between connected components. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Keep in mind this high-quality o-ring is made of durable rubber material and is sold as an individual item. It is a genuine item that is supplied by the original equipment manufacturer for use with DeWALT and Porter Cable impact drivers.

Washer - Urethane

$6.51

Fix Number: FIX11928144
Manufacturer Part Number: 642883-00

This is an authentic OEM part used in DeWALT and Porter Cable impact drivers. It fits between the anvil assembly and the sleeve. If it becomes lost or broken it will need replacing and a screwdriver may be needed during the installation. This part is made of urethane, a hard plastic, and is available individually.

Installation Instructions

james r from dixon, IL

broken ear

split case and slide out broken one and slide in new one and reinstall case. Read more...

COLLAR SA

$9.42

Fix Number: FIX18995774
Manufacturer Part Number: N922985

This is a genuine OEM replacement part used with the PCCK640LB (Type 1) 20V Impact Driver. The Porter Cable collar assembly is composed of metal and plastic items. This part secures the rubber sleeve to the motor & gearbox. The collar assembly is sold individually. A screwdriver and a pick set are helpful in the repair.

Hog Ring

$6.51

Fix Number: FIX11929390
Manufacturer Part Number: N053863

This authentic hog ring is sold individually. This part is found in impact drivers, and fits into a groove on the end of the anvil, holding the chuck assembly together. This is a common wear part that can lose tension, fall off, and ultimately cause the chuck to come completely apart. This is a simple repair that anyone can do. You will start by removing the hog ring from the chuck, being careful not to lose the small parts once the hog ring is removed. Next, install the compression spring, insert the plain washer, and replace the hog ring. You may need a pair of needle-nose pliers to help compress the spring while you insert the new hog ring.

Sleeve

$8.51

Fix Number: FIX11929419
Manufacturer Part Number: N078437

This is a genuine OEM part. The DeWALT sleeve is constructed of metal, and is compatible with several impact drivers. This component is fitted in the nose cone, between the spring and washer. The sleeve secures the anvil assembly and the spring. This part is sold individually. A hex key and a screwdriver may be helpful in the repair.

Drill Compression Spring

$6.51

Fix Number: FIX11929418
Manufacturer Part Number: N078434

This compression spring is for drills. The compression spring holds tension against the anvil and sleeve to keep the anvil tight on the armature. Disconnect the power before installing this part. Wear work gloves to protect your hands.

Plain Washer

$6.51

Fix Number: FIX11929226
Manufacturer Part Number: N016823

This is a genuine OEM plain washer and is part of your impact driver chuck assembly. The washer fits over the compression spring and provides a flat surface for the hog ring to sit against. This part usually needs to be replaced because it has been lost during the disassembly of the chuck. To begin this repair, remove the hog ring from the chuck, being mindful not to misplace the spring. Now you can place the compression spring in place and the new washer over top and reinstall the hog ring. Use a pair of needle nose pliers to push the compression spring as you install the hog ring over the spindle.

Porter Cable Impact Driver Parts

Popular Porter Cable Impact Driver Parts

Installation Instructions

Porter Cable Impact Driver Appliance Types

Popular Porter Cable Impact Driver Models

Porter Cable Impact Driver Parts

Start With Your Model Number

Popular Porter Cable Impact Driver Parts

Installation Instructions

Porter Cable Impact Driver Appliance Types

Popular Porter Cable Impact Driver Models