OEM Makita Hammer Drill Parts & Accessories

Carbon Brush Set

$14.64

Fix Number: FIX11885917
Manufacturer Part Number: CB351

This is a Genuine Manufacturer Sourced replacement part used on Makita Rotary Hammers. Includes Two (2) Carbon Brushes with Lead Wires attached. Please note Brush Holders and Springs are Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time. You would need a Screwdriver and Pliers to complete this job.

Watch the install video

Carbon Brush Set

$11.35

Fix Number: FIX10156652
Manufacturer Part Number: CB325

Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Carbon Brush Set

$16.66

Fix Number: FIX10156644
Manufacturer Part Number: CB175

This is a set of two carbon brushes with the lead wire attached. Please note that the holder and spring are sold separately. Some models will display a red indicator light when the carbon brushes are worn and require servicing. Poor motor performance or a tool that will not turn on are also strong indications that the carbon brushes may require replacement. To get access to the carbon brushes you will need a hex key/Allen wrench to open the housing.

Watch the install video

Cord Guard

$6.51

Fix Number: FIX10153918
Manufacturer Part Number: 682502-4

This is a cord guard, also known as a strain reliever, for your power tools. Power tool cords go through a lot of stress during usage, and this part is designed to remove some of that stress from the weakest point, which is where the cord meets the tool. Depending on how often you use your power tool, your cord guard will deteriorate. When this happens, you should replace it immediately. Keeping a strong power cord guard will help your tool live a longer life.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Watch the install video

Power Cord

$35.26

Fix Number: FIX10153834
Manufacturer Part Number: 664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Ball Bearing 6000ddw

$15.78

Fix Number: FIX10141492
Manufacturer Part Number: 210059-1

This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.

Ball Bearing

$9.63

Fix Number: FIX10141475
Manufacturer Part Number: 210023-2

This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

O-ring

$7.91

Fix Number: FIX10142024
Manufacturer Part Number: 213962-5

This replacement o-ring is specially designed for use with Makita rotary hammers. It is an authentic manufacturer sourced item that is used to provide a seal for the striker and the piston. For correct location please make sure to check appropriate diagrams of your unit. Over time seals and o-rings tend to shrink, become brittle and crack eventually requiring replacement. Please note one durable rubber o-ring is included per order. Replacing this item you would need hex key which is also known as an allen wrench to complete the repair.

Ball Bearing

$26.20

Fix Number: FIX10141520
Manufacturer Part Number: 211031-6

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Watch the install video

Carbon Brush Set

$19.19

Fix Number: FIX10156656
Manufacturer Part Number: CB407

This set comes with two carbon brushes with wire leads and brush strings attached. If your motor is not running efficiently or is operating intermittently, this is a common sign of worn brushes. Due to the friction they are constantly under, they will wear over time, and will start to appear cracked, pitted, or burnt if not replaced regularly. We recommend also taking a look at the armature to ensure it is not damaged. This brush set is compatible with multiple model types, so it is best to consult your user manual for repair instructions.

Makita Hammer Drill Parts

Popular Makita Hammer Drill Parts

Installation Instructions

Installation Instructions

Makita Hammer Drill Appliance Types

Related Makita Hammer Drill Parts

Popular Makita Hammer Drill Models

Makita Hammer Drill Parts

Start With Your Model Number

Popular Makita Hammer Drill Parts

Installation Instructions

Installation Instructions

Makita Hammer Drill Appliance Types

Related Makita Hammer Drill Parts

Popular Makita Hammer Drill Models