Sander Parts

Carbon Brush Set

$14.14

Fix Number: FIX10156653
Manufacturer Part Number: CB340

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. rnThis brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Carbon Brush Set

$10.85

Fix Number: FIX10156641
Manufacturer Part Number: CB154

This motor brush set is for power tools. Motor brush set transfers electric current to the spinning armature in the motor. The set includes both motor brushes.

Watch the install video

Carbon Brush Set CB-325

$6.19

Fix Number: FIX10156652
Manufacturer Part Number: CB325

Carbon Brush Set CB-303

$10.85

Fix Number: FIX10156649
Manufacturer Part Number: CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Watch the install video

Grinder Motor Brush

$7.87

Fix Number: FIX10106782
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Watch the install video

Power Cord

$21.97

Fix Number: FIX10153834
Manufacturer Part Number: 664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Bearing

$4.99

Fix Number: FIX10188435
Manufacturer Part Number: N110359

This authentic ball bearing is sold individually. It can be used in a variety of differently model types, such as miter saws, circular saws, table saws, and angle grinders. This ball bearing is sealed on both sides. Its job is to minimize friction between rotating parts. The armature rotates at a very fast rate, so after years of use, it is normal for the bearings to wear.

Carbon Brush Set CB-204

$26.23

Fix Number: FIX10156646
Manufacturer Part Number: CB204

This is a set of two OEM carbon brushes with wire leads and brush springs. To ensure your motor is running efficiently, it is important to continually inspect the carbon brushes, as they are a common wear part. If they are damaged this will greatly affect the performance of the motor. If burns or cracks are present, it is advised to inspect the armature as well.

Watch the install video

Complete Backing Pad

$10.26

Fix Number: FIX10140177
Manufacturer Part Number: 158324-9

This is a genuine Makita replacement part, it is sold individually. It has a soft foam pad with a metal backing. It has six vacuum holes for use with the 166078-4 Dust bag. It is remove by unscrewing four 266020-6 Screws. The sandpaper is held by two clamps on the base assembly.

Power Cord - 8', 14 Gauge, 2-Wire

$29.38

Fix Number: FIX10153852
Manufacturer Part Number: 664463-0

This power cord includes 2 prongs, 2 wires, and the gauge is 14. The measurement is 8 feet long and the type is bare wire. The cord is used on various power tools, specifically gardening and lawn equipment. With use and time, power tool cords can become frayed. If there are visible signs of wear on your cord, it is important to replace it immediately. For safety practices and installation instructions, refer to the diagram provided by the manufacturer.

Popular Sander Parts

Installation Instructions

Brands

Related Pages

Popular Sander Models

Sander Parts

Start With Your Model Number

Popular Sander Parts

Installation Instructions

Brands

Related Pages

Popular Sander Models