Drill Parts

Grinder Grinder/Sander Rotor Blade

$12.43

Fix Number: FIX12145308
Manufacturer Part Number: 1906PT

This part is sourced directly from Dotco and is designed to work with various Dotco and Cleco Grinders and Sanders. For full compatibility, please see the "Model Cross Reference List" below. The Rotor Blade is responsible for producing airflow inside the cylinder. If your tool has less power than before, it may be a sign that you have damaged Rotor Blades. If your Rotor Blades are cracked, chipped, or damaged, your tool will not operate properly, and they need to be replaced. Each blade is approximately 1" long, and are sold individually.

Blades/rotor (4 Pack)

$42.41

Fix Number: FIX10336518
Manufacturer Part Number: 01011

These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check the condition of the blades and replace them if they are visibly worn out or misaligned. Additionally, pay attention to any unusual signs during operation, such as increased noise, vibration, or burning smells. To replace the blades, refer to your user manual for detailed instructions on how to disassemble the motor housing. Typically, you will need to secure the tool in a padded vise, then use an adjustable pin wrench to remove the lock ring. Proceed with disassembling the tool by removing the collet and rotor nut from the rotor shaft, followed by the cylinder, spacer, and the four blades from the rotor.

SHIFTER BUTTON

$6.51

Fix Number: FIX12525746
Manufacturer Part Number: N397466

Seal

$8.92

Fix Number: FIX10336573
Manufacturer Part Number: 01464

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench to replace this item.

Vane Pack

$22.31

Fix Number: FIX12096546
Manufacturer Part Number: 7811R-42-6

Rotor Blade

$10.02

Fix Number: FIX10304441
Manufacturer Part Number: 864234

This part is an OEM from Cleco for use in nutrunners, grinders, and drills. The rotor blade attaches to the rotor and is made out of metal. If it becomes broken it will need to be replaced and may require a nutdriver during the installation. Keep in mind this high-quality part is sold individually.

Valve Seat

$22.31

Fix Number: FIX12094975
Manufacturer Part Number: 131-303

This is an original part from Ingersoll Rand. The valve seat is compatible with several impact wrenches, allowing the valve to be secured onto the housing interior. A wrench is often necessary for the replacement, and the valve seat is sold individually.

KEYLESS CHUCK

$48.35

Fix Number: FIX12523203
Manufacturer Part Number: N454251

Quick bit changes depend on a keyless chuck that turns smoothly and grips securely by hand. Rust, damaged jaws, or worn threads can cause poor holding force and uneven drilling. Clean the chuck and test another bit before ordering a replacement. Match the new chucks capacity and thread to the full tool model and parts diagram. Disconnect the battery, wear eye protection, and check the service manual because the retaining screw may loosen differently from a normal screw. Test the drill at low speed after installation.

Rotor Blade Set

$17.55

Fix Number: FIX10300599
Manufacturer Part Number: CA144889

This is a rotor blade set for your power tool, most commonly your angle grinder. The blades attach to the rotor, and push air inside your unit. This package includes 4 compound material blades. Replacing the blades will require a set of wrenches and a pair of pliers.

Blades

$40.43

Fix Number: FIX10336584
Manufacturer Part Number: 01480

These authentic OEM sourced replacement rotor blades are commonly used on Dynabrade sanders and grinders. They are attached to the rotor inside the tool pushing the air. This set includes (4) compound material blades per order. Replacing these blades you will need a set of wrenches and pliers.

Popular Drill Parts

Drill Brands

Related Drill Parts

Popular Drill Models

Drill Parts

Start With Your Model Number

Popular Drill Parts

Drill Brands

Related Drill Parts

Popular Drill Models