Drill Seals and Gaskets

Popular Drill Seals and Gaskets

Seal
$35.86
In Stock
Fix Number
FIX10132361
Manufacturer Part Number
45-06-0635
This is a Genuine Manufacturer Sourced replacement part designed for use with Milwaukee Drills. This part is made out of Metal and Rubber Material. This part provides a seal for Water Swivel Housing. There are Two (2) of these Seals on each end of Water Swivel Housing. Please note this item is Sold Individually. To complete this repair you would need a Screwdriver and Pliers.
O-ring
$4.13
In Stock
Fix Number
FIX10142022
Manufacturer Part Number
213960-9
O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> • O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> • O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> • O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> • O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.
Seal
$7.22
In Stock
Fix Number
FIX10336573
Manufacturer Part Number
01464
This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench to replace this item.
O Ring 14
$5.37
In Stock
Fix Number
FIX10141777
Manufacturer Part Number
213162-7
It is a genuine OEM sourced item that is specially manufactured for use with Makita power tools. An o-ring is generally used to create a tight seal between two connected parts. Please note this replacement item has multiple uses depending on the model of your tool, make sure to refer to appropriate diagrams for correct application of this o-ring. Over time the material may deteriorate and crack, inspect the seals and o-rings periodically, and replace them as needed to maintain peak performance. This high quality rubber o-ring is sold individually.
Endplate Gasket
$5.69
In Stock
Fix Number
FIX12096545
Manufacturer Part Number
7811R-283
O-ring
$5.16
In Stock
Fix Number
FIX10340248
Manufacturer Part Number
95730
It is a genuine replacement o-ring which is supplied by the original equipment manufacturer for use with Dynabrade power tools. This item is utilized to provide an air-tight seal between connected parts, please make sure to check appropriate diagram of your model for the correct use and location of this component. Over time o-rings tend to deteriorate and crack eventually requiring replacement to maintain peak performance. It is a high-quality part that is made of durable rubber material and it is sold individually.
O Ring 9
$5.16
On Order
Fix Number
FIX10141751
Manufacturer Part Number
213073-6
Gasket
$5.15
In Stock
Fix Number
FIX10173732
Manufacturer Part Number
450485-00
This is an original replacement part sourced directly from the manufacturer. The gasket is commonly found in drills from DeWALT and Black & Decker. This part is made of flexible plastic, and is used to seal the connection between the gear case cover and the gear case. You will require a screwdriver when replacing this item. The gasket is sold as an individual replacement part.
O-ring
$5.16
On Order
Fix Number
FIX10336527
Manufacturer Part Number
01024
This replacement o-ring is an original Dynabrade part that is specially produced for use with sanders, drills and grinders. It is an authentic OEM item that has multiple uses depending on your equipment, please make sure to check appropriate diagrams for correct location and use of this o-ring. Note one durable rubber o-ring is included per order.
O Ring 67
$5.16
In Stock
Fix Number
FIX10141995
Manufacturer Part Number
213720-9

Drill Seal or Gasket Brands