DeVilbiss Compressor Parts

DeVilbiss Appliance Parts

Popular DeVilbiss Compressor Parts

Fan Blade
$13.11
In Stock
Fix Number
FIX18991056
Manufacturer Part Number
AC-0108
This fan is an OEM direct from Craftsman for air compressors. This part cools the air compressor and connects to end of the motor shaft to prevent the air compressor from overheating. You will need a screwdriver, a socket set and a power drill to replace this part. This fan is made of plastic and is sold individually.

Installation Instructions

Steven from Darlington, SC
Air compressor was over heating and wouldn't restart after the first shut off.
Remove 1 Torx screw on end where air feeds into tank itself. Remove 2 Torx screws on other end. Pry cover apart. There are tabs that hold cover together. Remove screw that holds fan on. (my fan had dry rotted and had fallen off) Move shaft to lowest position and turn fan where hole is at the bottom. Slide onto shaft and replace bolt. Spin fan by hand to make sure it will rotate without going outside of where the cover will be when it is replaced. Put back cover on and replace the single screw. Snap front cover on and replace last 2 screws. You should be done. Plug up compressor and make sure it works correctly. Read more...
DRAIN VALVE
$8.64
Special Order
★★★★★
★★★★★
3 Reviews
Fix Number
FIX12508562
Manufacturer Part Number
N286039
This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.
Fixes these symptoms

Installation Instructions

Steven from SMITHS STA, AL
Wouldn't hold air in tank.
Took old drain valve out and replaced with new one. Read more...
Gasket
$7.83
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX9964140
Manufacturer Part Number
5140118-80
It is a genuine manufacturer sourced replacement part that is specially designed for Craftsman air compressors. This gasket provides an air-tight seal for the cylinder head assembly. Over time gaskets tend to get compressed, become brittle and crack eventually requiring replacement to maintain peak performance. It is made from durable, high quality composite material and it is sold individually.
TUBE SEAL
$6.51
Special Order
★★★★★
★★★★★
2 Reviews
Fix Number
FIX12522478
Manufacturer Part Number
N044359
This is a tube seal used with various power tools. The seal prevents air from leaking out of your equipment. It is placed on the outlet tube, and connected to the head of the compressor. Note that this part is sold individually. If you are having trouble with your air pressure, you may need to replace this part.
Fixes these symptoms
ORING P/L HEAD
$6.51
In Stock
Fix Number
FIX12513125
Manufacturer Part Number
ACG-45
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • <u>Extrusion and Nibbling</u> - The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.
KIT COMP RING REPLAC
$90.80
In Stock
★★★★★
★★★★★
5 Reviews
Fix Number
FIX12518127
Manufacturer Part Number
K-0650
This service kit repairs the piston cylinder area in select oil free air compressors, it can help when a worn sleeve or ring keeps the unit from building pressure, the kit includes the main parts and seals needed for the repair, release all stored air and disconnect power before installation, use the exact model and type number to confirm fit.
Fixes these symptoms

Installation Instructions

Ray from Derby, CT
low air pressure
removed head and air tube, reassembled same Read more...
★★★★★
★★★★★
6 Reviews
Fix Number
FIX18993125
Manufacturer Part Number
N008792
This air compressor regulator repair kit restores proper pressure control and airflow by replacing worn internal components such as seals and the piston. Designed to address leaks or inconsistent pressure, it helps return the regulator to reliable working condition. Replacing damaged parts with this kit can improve performance and ensure consistent operation.
Fixes these symptoms

Installation Instructions

Chris from LUBBOCK, TX
Compressor wouldn’t regulate the air.
I replaced the regulator but it was missing a key component. The peice behind the knob that actually regulates the air. Waste of money. Read more...
O-RING
$6.51
In Stock
Fix Number
FIX18991071
Manufacturer Part Number
AC-0781
This O-ring tube seal helps create an airtight connection where the tube enters the compressor head, supporting proper pressure and efficient operation. Made from durable rubber, it is designed to withstand heat and wear during regular use. Replacing a worn or damaged seal can help prevent air leaks and restore consistent compressor performance.Provide your feedback on BizChat

Installation Instructions

Christopher from BOONE, NC
cracked feed tube for compressor
just loosen up the plastic cover and work it out of there.
no need to disassemble the entire compressor
Read more...
★★★★★
★★★★★
1 Review
Fix Number
FIX10049057
Manufacturer Part Number
N036518
This is a Genuine OEM replacement part designed for use with Air Compressors. This kit Includes: Piston Rod, Compression Ring , Cylinder Sleeve & Bearing. Please note that this kit does not include the valve plate, head gaskets, or any other compressor parts. Replacing this kit you would need a Screwdriver, Hex Key/Allen Wrench and Pliers.
Fix Number
FIX12543085
Manufacturer Part Number
Z-D24819
This is a manufacturer-approved head gasket for an air compressor, sold individually. It is designed to seal the valve plate to the cylinder head. If this gasket is damaged or worn, this can create an air leak from the head, which will make it so the compressor is no longer pressurizing the tank. For this repair you will need the following tools: Philips screwdriver, torx drivers, flat-blade screwdriver, long-nosed pliers, impact driver or socket wrench, and a torque wrench.
Fixes these symptoms

DeVilbiss Compressor Appliance Types

Related DeVilbiss Compressor Parts

Popular DeVilbiss Compressor Models