Black and Decker Compressor Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Black and Decker Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Black and Decker Compressor Parts

O-RING – Part Number: AC-0781
O-RING
$6.51
In Stock
Fix Number
FIX18991071
Manufacturer Part Number
AC-0781
This is a rubber O-ring for a compressor. It creates a seal for the tube as it enters the head. This part is sourced directly from the original manufacturer, ensuring it is the correct fit. It measures approximately 0.362 in inner diameter and 0.103 in outer diameter. Over time, the O-ring can begin to wear and should be replaced to maximize the power of your air compressor. Before you begin this repair, you will need to unplug the unit and bleed air from the tank.

Installation Instructions

Christopher from BOONE, NC
cracked feed tube for compressor
just loosen up the plastic cover and work it out of there.
no need to disassemble the entire compressor Read more...
Watch the install video
TUBE SEAL – Part Number: N044359
TUBE SEAL
$6.51
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX12522478
Manufacturer Part Number
N044359
This is a tube seal used with various power tools. The seal prevents air from leaking out of your equipment. It is placed on the outlet tube, and connected to the head of the compressor. Note that this part is sold individually. If you are having trouble with your air pressure, you may need to replace this part.
Fixes these symptoms
Watch the install video
DRAIN VALVE – Part Number: N286039
DRAIN VALVE
$7.91
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX12508562
Manufacturer Part Number
N286039
This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.
Fixes these symptoms

Installation Instructions

Steven from SMITHS STA, AL
Wouldn't hold air in tank.
Took old drain valve out and replaced with new one. Read more...
Watch the install video
REGULATOR REPAIR KIT – Part Number: N008792
REGULATOR REPAIR KIT
$41.93
In Stock
★★★★★
★★★★★
6 Reviews
Fix Number
FIX18993125
Manufacturer Part Number
N008792
This is an OEM regulator repair kit for air compressors. This kit contains all the parts and instructions needed to restore a broken regulator. It is normal for the inner parts of the regulator to wear and have to be repaired over time. Before beginning this repair make sure you release the pressure from the air tank.
Fixes these symptoms

Installation Instructions

Chris from LUBBOCK, TX
Compressor wouldn’t regulate the air.
I replaced the regulator but it was missing a key component. The peice behind the knob that actually regulates the air. Waste of money. Read more...
Connecting Rod And Piston Asse – Part Number: N038785
Connecting Rod And Piston Asse
$69.69
In Stock
Fix Number
FIX10187559
Manufacturer Part Number
N038785
This is an OEM connecting rod and piston assembly for an air compressor. This assembly includes the cylinder tube, valve plate O-rings and a complete piston including the bearing. This assembly is usually replaced because of low compression. For this repair you will need a screwdriver and wrench.
Fixes these symptoms
ORING P/L HEAD – Part Number: ACG-45
ORING P/L HEAD
$6.51
In Stock
Fix Number
FIX12513125
Manufacturer Part Number
ACG-45
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • <u>Extrusion and Nibbling</u> - The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.
Watch the install video
Belt – Part Number: N011005
Belt
$53.98
In Stock
Fix Number
FIX10187047
Manufacturer Part Number
N011005
This part includes one black rubber belt for a compressor. It is sourced right from the original manufacturer. Over time, the belt can become brittle and break and will need to be replaced when this happens. This belt is driven by the electric motor, and attaches to the flywheel, motor shaft and idler pulley. It measures 30-1/2-Inches long overall, 14-1/4-Inches at half length, 5/8-Inches wide, and has a thickness of 0.065-inches with teeth.
Fan Blade – Part Number: AC-0108
Fan Blade
$14.47
In Stock
Fix Number
FIX18991056
Manufacturer Part Number
AC-0108
This fan is an OEM direct from Craftsman for air compressors. This part cools the air compressor and connects to end of the motor shaft to prevent the air compressor from overheating. You will need a screwdriver, a socket set and a power drill to replace this part. This fan is made of plastic and is sold individually.

Installation Instructions

Steven from Darlington, SC
Air compressor was over heating and wouldn't restart after the first shut off.
Remove 1 Torx screw on end where air feeds into tank itself. Remove 2 Torx screws on other end. Pry cover apart. There are tabs that hold cover together. Remove screw that holds fan on. (my fan had dry rotted and had fallen off) Move shaft to lowest position and turn fan where hole is at the bottom. Slide onto shaft and replace bolt. Spin fan by hand to make sure it will rotate without going outside of where the cover will be when it is replaced. Put back cover on and replace the single screw. Snap front cover on and replace last 2 screws. You should be done. Plug up compressor and make sure it works correctly. Read more...
Gasket – Part Number: 5140118-80
Gasket
$8.64
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX9964140
Manufacturer Part Number
5140118-80
It is a genuine manufacturer sourced replacement part that is specially designed for Craftsman air compressors. This gasket provides an air-tight seal for the cylinder head assembly. Over time gaskets tend to get compressed, become brittle and crack eventually requiring replacement to maintain peak performance. It is made from durable, high quality composite material and it is sold individually.
Watch the install video
VALVE PLATE ASSY – Part Number: N017592SV
VALVE PLATE ASSY
$23.10
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX12517182
Manufacturer Part Number
N017592SV
This is a valve plate for your compressor or generator. This part controls the air flow into the pump. When the air is pumped by the piston, it passes through the valve plate and into the compressor tank. The most common sign of a damaged valve is if your pressure is not building up in the tank. The reeds on the valve plate are usually the first thing to wear out. If you notice visible damage on the reeds you will need to replace this part. This valve includes the plate, and the lower gasket. The head gasket is sold individually.
Fixes these symptoms

Installation Instructions

Ray from Derby, CT
low air pressure
removed head and air tube, reassembled same Read more...

Black and Decker Compressor Appliance Types

Related Black and Decker Compressor Parts

Popular Black and Decker Compressor Models

View More
+