Whirlpool/Whirlpool_Thumb/0XW0IVKY.gif
See part 7 in the diagram
( Grid squares measure 1x1 inch )

Retaining Ring

$8.72
Fix Number: FIX11746917
Manufacturer #: WP9703680
Manufactured by: Whirlpool

Product Description

Used on Stand Mixers.

Questions and Answers

Questions and Answers

Be the first to ask our experts a question about this part!

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.3 / 5.0, 7 reviews.
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
  • Customer:
    carol from whittaker, MI
  • Parts Used:
    W11086780, WP9703680, W11192795
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
mixer skipped while turning
followed instructional video the hardest part was removing the snap ring! once that was removed it was a piece of cake!
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Alan from Mercer, PA
  • Parts Used:
    WP9703680, W11192795
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
The Bevel Gear had stripped several teeth off
1.Remove Mixer top (4 screws) 2.remove gear case cover (4 screws) 3. Remove old retaining ring 4. Lift old bevel gear from shaft. 5. Remove retaining pin from shaft and drop shaft out bottom 6. Remove ALL old grease making sure to get all metal pieces from old bevel gear. 7. inspect all gears for damage 8. replace shaft and retaining pin 9. Place new bevel gear onto shaft and secure with retaining ring 10 Install new grease liberally 11. replace gear cover case and secure with 4 screws 12. Replace case top and secure with 4 screws
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    lisa from SAINT HELENA, CA
  • Parts Used:
    W11086780, WP9703680
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
Stripped work gear- mixer wouldn't spin
Unplugged kitchen aide pro mixer
Used a square bit on drill to unscrew trim piece from mixer
Used same bit to remove top of mixer and again to expose the gears.
Used special pliers to remove the retaining ring.
Pulled off the top gear
Slid out a pin
Pulled off the worm gear
Replaced worm gear replaced pin replaced top gear used pliers to replace retaining ring.
Reassembled the mixer with drill.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noise and no motion
1 Open case and get to the gear assembly 2 remove snap ring and remove gear
3 remove pin and remove and replace gear
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Bruce from Naperville, IL
  • Parts Used:
    W11086780, WP9703680
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
Gear badly worn
replaced gear
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Accessory input port striped. Not driving attachment.
Problem found is plastic transmission cover cracked causing too much play between gears causing them to skip and strip. New replacement cover is cast metal. Great improvement. Remove trim ring (one screw). Remove top cover (4 screws). Remove plastic transmission cover (4 screws). Remove snap ring that holds too beveled gear. Replace gear and re install snap ring. Replace gear in transmission (other beveled gear) I also replace bronze bushings at each end of the adjacent worm gear. Re pack all gears and transmission cover with fresh grease. Reinstall all gears and transmission cover. Ensure all components are properly seated and lined up. Re instal cover and trim ring. Easy fix. Less than an hour. Works as good as new. Replacement parts fit perfectly.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Richard from Butte, MT
  • Parts Used:
    WP9707223, WP9703680, W11192795
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Bevel gear broke
Took it apart. Saw the broken gear. Got online and ordered the parts and completed the repair as soon as the parts came.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Model Compatibility
This part works with the following models:
Fix Number: FIX11746917
Manufacturer Part Number: WP9703680
Brand
Model Number
Description
Whirlpool
3KSM6583TER0
Mixer
Whirlpool
3KSM6583TGU0
Mixer
Whirlpool
3KSM6583TWH0
Mixer
Whirlpool
3KSMC895TWH0
Mixer
KitchenAid
4KB25G1XBU3
Mixer
KitchenAid
4KB25G1XBU5
Mixer
KitchenAid
4KB25G1XBY5
Mixer
KitchenAid
4KB25G1XCO5
Mixer
KitchenAid
4KB25G1XER3
Mixer
KitchenAid
4KB25G1XER5
Mixer
KitchenAid
4KB25G1XGA5
Mixer
KitchenAid
4KB25G1XMC5
Mixer
KitchenAid
4KB25G1XMY5
Mixer
KitchenAid
4KB25G1XOB3
Mixer
KitchenAid
4KB25G1XOB5
Mixer
KitchenAid
4KB25G1XTG3
Mixer
KitchenAid
4KB25G1XTG5
Mixer
KitchenAid
4KB25G1XWW3
Mixer
KitchenAid
4KB25G1XWW5
Mixer
KitchenAid
4KD2661XMC3
Mixer
KitchenAid
4KG25G0XMC4
Mixer
KitchenAid
4KG25G0XWH4
Mixer
KitchenAid
4KG25G7XER4
Mixer
KitchenAid
4KG25G7XOB4
Mixer
KitchenAid
4KG25G7XSL4
Mixer
KitchenAid
4KG25G7XWH4
Mixer
KitchenAid
4KG25H3XER5
Mixer
KitchenAid
4KG25H3XOB5
Mixer
KitchenAid
4KG25H3XSL5
Mixer
KitchenAid
4KG25H3XWH5
Mixer