Models
>
3KSM6583TER0
3KSM6583TER0 Whirlpool Mixer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 3KSM6583TER0
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
$7.88
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
$6.54
This is a genuine OEM Torx screw that measures 7-18 and 3/4-inch. The screw is sold individually and can be used in a variety of appliances. The star shaped head allows the screw to have more torque a...
In Stock
In Stock
In Stock
$10.08
This is a replacement bowl arm lift for your stand mixer. It raises and lowers the mixing arm in the bowl. It is made of white plastic and is sold individually. This part can also be known as the bowl...
In Stock
$34.34
This part is the replacement wire whip for your stand mixer. It is made of metal and is approximately 7 inches from top to bottom, and 5 inches from side to side. The wire whip is an attachment which ...
In Stock
$26.06
The Coated Flat Beater is an OEM accessory specifically designed for 5 and 6 Quart KitchenAid stand mixers. This flat beater is responsible for thoroughly incorporating ingredients when mixing or blending recipes.
In Stock
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 3KSM6583TER0
Viewing 3 of 3Noisy
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Charlotte, NC
- Parts Used:
- WP9706885
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The mixer would not raise the bowl
I removed the motor assembly from the mixer. This left the stand assembly. The raising lift arm had to be removed by unscrewing the set screw, and then the lift arm was removed. I replaced the plastic arm bowl lift by sliding it over the lift arm, and then I had to remove the spring with a clip washer with the pliers, and replaced the spr
... Read more
ing back on to the new part. Total time about ten minutes for the actual fix, and about 45 minutes remove and reinstall the 12 screws that held the motor in place. It was well worth my efforts. The mixer arm works perfectly now.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from ENDWELL, NY
- Parts Used:
- WP9708649
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
all four feet on mixer damaged
I first ahd to remove the original feet by removing screws that held them in place. The new feet that I purchased were different then the original. They were a push in type and not held in by screws. I had to modify the base by drilling the foot holder to accept the new style feet. Once this was done, the feet were installed and looke
... Read more
d good.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SAINT LOUIS, MO
- Parts Used:
- WP9708649
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed to replace rubber foot on mixer
The insertion part of the foot was tapered to fit in the hole in the mixer. Simple pressure was not the answer. So I used a small key, placed it on the bottom of the foot, after applying a little vegetable oil on the foot, and tapped it into place. Worked well.Joe
Was this instruction helpful to you?
Thank you for voting!