See part 30 in the diagram
( Grid squares measure 1x1 inch )
Light Socket - 250V 75W
$28.53
In Stock
Fix Number: FIX230544
Manufacturer #: WB08X10016
Manufactured by:
GE
-
Product Description
Light bulb not included.
-
Works with the following brandsGeneral Electric, Hotpoint, Kenmore
-
Works with the following productsMicrowave, Range
-
Fixes the following symptomsWon’t turn on
-
Part Number Cross ReferencePart# WB08X10016 replaces these:AP3669152, 769460, WB08X10016, WB08X0310, WB08X10011, WB08X10017, WB8X10011, WB8X10016, WB8X10017, WB8X310
Product Description
Light bulb not included.
-
Works with the following brands:General Electric, Hotpoint, Kenmore
-
Works with the following products:Microwave, Range
-
Fixes the following symptoms:Won’t turn on
-
Part# WB08X10016 replaces these:AP3669152, 769460, WB08X10016, WB08X0310, WB08X10011, WB08X10017 ... Show more , WB8X10011, WB8X10016, WB8X10017, WB8X310 Show less
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related PartsAdditional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
-
Customer:Pamela from Ocala, FL
-
Parts Used:WB08X10016
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
The light bulb overheated and fused with the socket.
I removed the bottom cover of the microwave. Unplugged the wiring harness. Replaced the damaged socket and inserted led bulbs so they would not overheat again. Put the screws back in the cover.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Mary Ann from Wyomissing, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Light bulbs broke off inside socket. Tried to screw bulb ot and the sockets broke into pieces
Turn off electricity and pull plug from appliance. Remove 5 or six screws from the bottom panel of appliance. This allows you easy access to remove bulbs and sockets. Remove the two screws from the sockets and remove the wires clipped into the sockets. remove damaged sockets and bulbs if both need to be replaced. Insert wires onto new parts and place back into unit.Replace bottom panel and your repair is complete. Thank you for the parts and helpful instructions from you customers. Made the repair really easy.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Alan from Albuquerque, NM
-
Parts Used:WB08X10016
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Down light would not turn on.
Replacing the bulb socket should take less than 15 minutes and require only a Phillips head screwdriver. Unless, as was my experience, you find that the connections at the rear of the socket are fried. The insulated connectors were brittle and one wire was hanging loose. In that case you will need (female) spade connectors of two sizes and have to carefully strip new ends on the wires which are very fine. Finish by wrapping the connectors with electrical tape.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Janet from Charlotte, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
the light bulbs were burnt out and broke at the base when I tried to replace them. Then the brittle sockets broke when I tried to loose the metal bases from the now broken light bulbs.
I took 5 screws out of the bottom of the microwave so I could get to the socket, took the single screw out that was holding the socket, slid the silicone sleeve wrapped electrical connectors off the broken socket and threaded them back onto the replacement sockets. Screwed the new sockets back it, replaced the bulbs, screwed the 5 screws back to hold the microwave base back up. All done! Maybe 5-7 minutes. Everything fit. Everything worked. Super Easy.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Arthur from Beavercreek, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Surface lights did not work
Dropped the bottom panel (4 Phillips screws) and removed the light sockets (1 Phillips screw on each socket) and the unplugged the wiring harness, this was a bit difficult as the shorting process required some jiggling to unplug ( I used a pair of needle nose pliers). Replaced the the harness and sockets in reverse order. This repair was very easy and it was obvious where the arcing took place when the bulb burned out. The harness and the sockets were bad and needed replacing however when they shorted out they also burned out the section of the control panel circuit board that controlled the lights and exhaust fan and that repair was a bit harder.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Cliff from Saugerties, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
stove light not working under microwave..bulb burned out and socket broke
5 screws to take out and one for the socket. screw in bulb and replace socket with one screw and done...so simple, simple, simple.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Keith from Gibsonburg,, OH
-
Parts Used:WB08X10016
-
Difficulty Level:Very Easy
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
Light Sockets And Wire Replace
Remove screws and reinstall
Was this instruction helpful to you?
Thank you for voting!
-
Customer:John from Eagan, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Replace surface lights and sockets
Ordered on Monday, received Wednesday morning. Took less than 10 minutes to replace the bulbs and sockets. The only problem is that the the micro switch is a 3-position. On, Nite Lite and Off. The replacement bulb is just On/Off. Really doesn't bother us all that much. Didn't see that we had a choice of bulbs.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Lawrence from South Nyack, NY
-
Parts Used:WB08X10016
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Light bulbs kept burning out
This was really simple. After making sure the power to the lights was off, I removed three phillips head screws from the light panel. This is located at the bottom of the microwave. I then slid the panel forward about a quarter inch to free it. I then lowered it and removed the one screw holding the light socket in place, pulled the light socket out, replaced with the new one and slid the 2 connecting wires onto the terminals on the socket. The terminals are different sizes so you can't make a mistake there.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX230544
Manufacturer Part Number: WB08X10016
Manufacturer Part Number: WB08X10016
Brand
Model Number
Description