Snow Blower Hardware

Fix Number

FIX9143890

Manufacturer Part Number

812000029

This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.

Fix Number

FIX9286886

Manufacturer Part Number

532187690

This is an OEM lawn mower deck mandrel spacer washer, sold individually. It measures approximately 43/64-Inches in diameter, 1-1/8-Inches outer diameter, and 5/32-Inches thick (these measurements are approximate). In general, washers help to spread load, can provide insulation such as electrical, and can also help to prevent galvanic corrosion.

Fix Number

FIX9015920

Manufacturer Part Number

532188967

This is a Genuine Manufacturer Approved replacement washer used on lawn and garden equipment. This part is made out of Metal and is Sold Individually. Washer helps to distribute the pressure evenly over the surface and provides a solid grip.

Fix Number

FIX9022497

Manufacturer Part Number

532409149

This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most models require three. For this repair you will need a wrench set.

Fix Number

FIX9096195

Manufacturer Part Number

714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.

Fix Number

FIX16381841

Manufacturer Part Number

596136401

Genuine Manufacturer Approved Carriage Bolt is a standard part that fits a variety of products. This part is sold individually and the Nut is not included. The square area under the head is designed to fit into a square hole in the workpiece. It is this square hole that restrains the bolt and keeps it from turning when the nut is tightened.

Fix Number

FIX16381824

Manufacturer Part Number

596134901

It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tight seal between connected parts, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this durable metal washer is sold individually.

Fix Number

FIX16381792

Manufacturer Part Number

596040501

This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.

Fix Number

FIX9026163

Manufacturer Part Number

532851084

This is an OEM part sourced directly from Husqvarna. This grade 8 hex head screw is made of metal and measures approximately 3/8 - 24 x 1 ? 3/8. This screw is commonly used in lawn mowers, snow blowers, and tillers. The use depends on the equipment type, for instance in lawn mowers it can be used to hold the blade in place, in the assembly of snow blowers it can be used to hold pulleys in place. This is why we recommend you refer to model specific diagrams for appropriate uses and applications. This screw is sold individually, and you will need a wrench to successful install it.

Fix Number

FIX9014802

Manufacturer Part Number

532191574

This manufacturer approved bolt is made for lawn and garden equipment. In conjunction with handle knob it helps to secure the upper and lower handles together. The way this bolt is designed, you will need no tools to replace it. The square area under the head is made to fit into a square hole of the handle. This opening restrains the bolt and keeps it from turning when the handle knob/nut is tightened. Includes one (1) bolt per order.