Cultivator Parts

Clevis Pin

$7.52

Fix Number: FIX9009427
Manufacturer Part Number: 532132673

This is a genuine component which is specially designed for use with Poulan, Husqvarna, Weed Eater and Jonsered tillers. It is supplied directly from the original equipment manufacturer. This item provides a high-quality replacement for a missing or a faulty hardware that was installed on a new unit. The clevis pin is installed in order to protect your tiller. If the auger gets jammed or clogged, the pin is designed to snap at a certain point of pressure, so it will not damage any other part of the unit. Please make sure to refer to the appropriate diagrams of your model for the correct application of this part. Keep in mind this high-quality clevis pin is made of durable metal and is sold individually. Replacing it is a simple task that should only require pliers to remove the old and secure the new.

Jaw Insert (3/4 In)

$20.38

Fix Number: FIX16390336
Manufacturer Part Number: 643492001

This PEX press tool jaw insert is used inside a crimping tool to grip and compress PEX crimp rings during installation. It helps ensure accurate, secure crimps for reliable pipe connections. Replacing a worn or damaged insert restores proper crimping performance and consistent results.

SWITCH

$23.60

Fix Number: FIX19501041
Manufacturer Part Number: 160720030T

LEVER

$6.51

Fix Number: FIX18792350
Manufacturer Part Number: 996804001

Control, Throttle

$32.27

Fix Number: FIX9014784
Manufacturer Part Number: 532189482

This is an authentic OEM part from Husqvarna for use with Tillers. The throttle control assembly attaches to the handle and the carburetor to control the engine speed. The most common reason for replacing the throttle control assembly is if the throttle is unresponsive, stuck open (or closed), the throttle cable is rusted, broken or the throttle trigger handle is broken or cracked. This part is sold individually. Here is a list of tools that are needed to replace the throttle control assembly wire cutters, long-nosed pliers, wrench socket/ratchet set and a small screwdriver.

Belt, V

$18.65

Fix Number: FIX17016528
Manufacturer Part Number: 591372401

This genuine OEM replacement drive belt is designed for use with rotary lawn mowers and garden tillers, providing a reliable connection between the engine and the cutting or tilling mechanism. Made from high-quality, durable rubber, this belt is built to withstand regular outdoor use and is sold individually. Replacing the belt is a relatively simple task that requires only a screwdriver. To perform the repair, first disconnect the spark plug to ensure safety. Then, remove the belt cover to access the old belt. After removing the worn belt, install the new one in its place, secure the cover, and reconnect the spark plug. Always consult your equipment’s manual for model-specific guidance and safety precautions.

Sleeve

$6.51

Fix Number: FIX16398265
Manufacturer Part Number: 692512002

This is a round metal sleeve with an approximate diameter of 3/4-inches, with a beveled centre with a 1/4-inch bore. It is sold individually, and sourced directly from the original manufacturer. The sleeve is part of the clamp assembly and is used to secure accessories to the tool.

Fuel Pick-Up Line with Filter

$14.53

Fix Number: FIX9136545
Manufacturer Part Number: 791-182353

This is a genuine OEM replacement part, it is sold individually. The purpose of the Fuel Pick--Up Line with Filter is to provide fuel into the carburetor via the primer bulb. The filter is situated inside the fuel tank,with the fuel line extending through an existing hole in the fuel tank. It is then connected to the primer bulb which will purge the air out of the carburetor. By pressing the primmer bulb it will fill the carburetor with fuel, once it is full the excess fuel will be forced back into the tank through the fuel return line. Over time the fuel filter will be come clogged with debris and will have to be changed.

Gasket, Gearcase

$28.55

Fix Number: FIX9018035
Manufacturer Part Number: 532431022

This is an authentic manufacturer sourced replacement part that is specially designed for use with gas powered lawn and garden equipment. The purpose of this gasket is to provide an air-tight seal for the gearcase. Over time gaskets tend to get compressed and deteriorate eventually requiring replacement. Please note one durable composite material gasket is included per order.

Tiller Chain (#35-50 Pitch)

$14.25

Fix Number: FIX9008326
Manufacturer Part Number: 532102134

This is an authentic OEM sourced replacement component which is specially produced for use with Craftsman tillers. It is the main chain that helps to drive the unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Over time the chain may wear out and stretch eventually requiring a replacement to ensure peak performance. Keep in mind this high-quality metal part is sold individually.

Popular Cultivator Parts

Cultivator Brands

Related Cultivator Parts

Popular Cultivator Models

Cultivator Parts

Start With Your Model Number

Popular Cultivator Parts

Cultivator Brands

Related Cultivator Parts

Popular Cultivator Models