Cultivator Hardware

Fix Number

FIX9022497

Manufacturer Part Number

532409149

This is a genuine hex flange locknut for a lawn mower. It attaches to the carriage bolt (sold separately), fastening the axle assembly braces in place. This part is sold individually, however most models require three. For this repair you will need a wrench set.

Fix Number

FIX16381824

Manufacturer Part Number

596134901

It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tight seal between connected parts, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this durable metal washer is sold individually.

Fix Number

FIX16381792

Manufacturer Part Number

596040501

This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.

Fix Number

FIX16381888

Manufacturer Part Number

596238701

This is a genuine OEM replacement part used on a variety of Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. This steel washer has several applications based on your unit. Please refer to diagrams for proper application.

Fix Number

FIX9092936

Manufacturer Part Number

712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

Fix Number

FIX9298768

Manufacturer Part Number

710-0599

This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches long, and has 20 threads per inch. This style is a hex head with a built-in washer that will cut its own threads in most predrilled steel.

Fix Number

FIX9299574

Manufacturer Part Number

712-04064

This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torque type lock nut, and it has no temperature or chemical restrictions. This part has a 1/4-inch diameter and 20 thread size.

Fix Number

FIX8950288

Manufacturer Part Number

32144-41

This is a self threading bolt designed for snowblowers. This OEM part is sourced directly from the original manufacturer. It is sold individually and has a thread of 5/16-inches. The self threading bolt is used to fasten the bushing and gear case assembly together.

Fix Number

FIX9009427

Manufacturer Part Number

532132673

This is a genuine component which is specially designed for use with Poulan, Husqvarna, Weed Eater and Jonsered tillers. It is supplied directly from the original equipment manufacturer. This item provides a high-quality replacement for a missing or a faulty hardware that was installed on a new unit. The clevis pin is installed in order to protect your tiller. If the auger gets jammed or clogged, the pin is designed to snap at a certain point of pressure, so it will not damage any other part of the unit. Please make sure to refer to the appropriate diagrams of your model for the correct application of this part. Keep in mind this high-quality clevis pin is made of durable metal and is sold individually. Replacing it is a simple task that should only require pliers to remove the old and secure the new.

Fix Number

FIX16381724

Manufacturer Part Number

595901601

This is a genuine OEM replacement part that is used for lawn mowers and tractors across a number of brands. This is standard hardware which has multiple applications based on your tool. Please refer to diagrams for proper application. It is made out of metal and it is sold individually. You would need a wrench to remove or install this bolt.