Craftsman Chainsaw Hardware

Craftsman Appliance Parts

Popular Craftsman Chainsaw Hardware

Screw
$6.51
In Stock
Fix Number
FIX12507350
Manufacturer Part Number
90639221
This part includes one official OEM screw (M5x8.5) for a chainsaw. This left-hand screw is located near the guide bar, underneath the chain cover, which will need to be removed to access it. This screw can wear over time, and will need to be replaced.
Washer
$6.51
In Stock
Fix Number
FIX12505518
Manufacturer Part Number
90618229
This is a washer, located underneath the chain cover by the guide bar of a chainsaw. This washer works with the screw to keep it secure (screw sold separately). Washers can warp or damage over time and require replacement. This washer is sold individually and sourced directly from the original manufacturer.
Fixes these symptoms
Nut-flglk 5/16-18
$6.51
In Stock
Fix Number
FIX9092936
Manufacturer Part Number
712-04063
This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.
Screw
$6.51
In Stock
Fix Number
FIX10169701
Manufacturer Part Number
330019-12
This replacement screw is a high quality hardware commonly utilized on Bostitch, Black and Decker, Porter Cable and Dewalt equipment. This is a authentic OEM item which has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.
Clip
$8.15
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX12636951
Manufacturer Part Number
530071945
This is a washer kit for a chainsaw. This kit includes the retaining washer, C-ring, and the washer that is located between the clutch and clutch drum assembly. The outer washer acts like a shoulder to keep the chain on the sprocket as well as helps secure the clutch drum to the saw. Due to its consistent contact with the chain, the outer washer is known to deteriorate over time. If the chain is regularly run with minimal tension, this will actually speed up the deterioration and cause the chain to move from side-to-side. The retainer C-clip should be replaced any time it has been removed. For this repair you will need to remove the side cover, the chain, and the bar.
Trimmer Screw
$6.84
In Stock
Fix Number
FIX8987845
Manufacturer Part Number
503217010
This is a genuine OEM approved replacement screw made for Husqvarna chainsaws and brush cutters. It is a standard hardware which has multiple uses based on your equipment. Please refer to diagrams for correct application. It is made out of metal and it is sold individually. You would need a torx screwdriver to install or remove this screw.
Screw
$6.51
In Stock
Fix Number
FIX10169702
Manufacturer Part Number
330019-14
It is a genuine replacement screw that is sourced directly from original equipment manufacturer. This is a standard hardware that has multiple uses depending your tool. For correct location and use of this screw, please check appropriate diagrams. This torx screw is sold individually.
Plastite Screw
$6.51
On Order
Fix Number
FIX9943617
Manufacturer Part Number
330019-04
This is a plastite screw for a variety of power tools. It is almost an inch long with a pan head. A plastite screw is needed when using harder plastics. It is more resistant to stripping and pulling out.
Screw
$6.84
In Stock
Fix Number
FIX9282603
Manufacturer Part Number
503212810
This screw is a genuine Husqvarna replacement item. It is supplied directly from original equipment manufacturer for use on chainsaws. It is a special screw that is used in various locations on the saws. To ensure if this is the correct screw that you are looking for, make sure to check appropriate diagrams for your model. This is a screw can be adjusted by a Phillips or a flat-head screwdriver. Please note, it is sold individually.
Nut
$6.84
In Stock
Fix Number
FIX9004113
Manufacturer Part Number
530015917
It is a genuine item that is supplied by the original equipment manufacturer for use with Craftsman chainsaws. This is the special nut that helps to secure the bar. It provides an identical replacement for a missing or a faulty hardware that was installed on a new unit. Please make sure to check the appropriate diagrams of your model for the exact location and application of this part. Keep in mind this high-quality bar nut is made of durable metal and is sold individually.

Related Craftsman Chainsaw Parts