OEM Jonsered Parts & Accessories

Lawn Tractor Mandrel Assembly

$48.56

★★★★★

1 Review

Fix Number: FIX12087499
Manufacturer Part Number: 587819701

Installation Instructions

Terrence from LORENA, TX

Blade mandrel replacement

1. Remove mower deck.
2. Remove mower blade from defective mandrel.
3. Clean caked up grass from underside of mower deck.
4. Remove belt pulley from top of defective mandrel.
5. Remove four bolts fastening defective mandrel to deck. Note: bolts will most likely shear - make sure you have new ones.
6. Install new mandrel to deck using four new self-tapping bolts.
7. Reinstall mower blade to new mandrel assembly.
8. Reinstall belt pulley to new mandrel assembly.
9. Reinstall mower deck to tractor. Read more...

Ring Klip Number T5304-75

$3.99

Fix Number: FIX9143890
Manufacturer Part Number: 812000029

This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.

Washer 25/32 x 1-1/4 x 16 Ga.

$3.99

Fix Number: FIX9008998
Manufacturer Part Number: 532121749

This is a flat metal washer found in various models of lawn mowers and is sold individually. This flat washer can have various functions depending on the equipment; however, its general purpose is to spread the load under a bolt or screw. It also helps to reduce heat and friction as the fastener is tightened. This repair may require a screwdriver or socket wrench, depending on the fastener for your model. This is a single flat washer; the fasteners are sold separately.

Wheel

$4.99

Fix Number: FIX12630280
Manufacturer Part Number: 589527301

Wheel.gage.half.spoked

Carburetor Gasket

$4.99

Fix Number: FIX9899150
Manufacturer Part Number: 16228-ZL8-000

This is a carburetor gasket and is sold individually. If your engine is running rough, it could be due to a worn or damaged gasket. The gasket is meant to provide an air tight seal, to help protect the engine. This gasket should be replaced when repairing the carburetor. When removing this part, it is advised to clean the surfaces around the carburetor gasket before installing the new one.

Mandrel Pulley Assembly

$11.20

Fix Number: FIX9015257
Manufacturer Part Number: 532195945

This mandrel pulley is for lawn tractors. Mandrel pulley spins the blade on the mower deck of the tractor. Wear work gloves to protect your hands when installing this part.

Gasket- Insulator

$7.97

Fix Number: FIX9899073
Manufacturer Part Number: 16212-ZL8-000

Sold individually, this insulator gasket is sourced directly from the manufacturer and is for small engines. This part acts as a seal between the cylinder housing and the carburetor insulator. This airtight seal is created to ensure contaminants do not make their way to the carburetor. It may become obvious that this part needs to be replaced if the engine keeps stalling or is running rough.

Blade High Lift

$17.43

Fix Number: FIX9015048
Manufacturer Part Number: 532180054

This is an OEM replacement part, sold individually. The High Lift Blade is also referred to as a 2 in 1 blade. It throws the clippings better, and is used when you are just discharging or bagging the grass clippings. If you want to Mulch your clippings you would want to purchase a Mulching Blade. This part is compatible with the mowers and tractors listed below. A wrench is needed for replacement.

Pulley Idler

$26.14

Fix Number: FIX9287043
Manufacturer Part Number: 532196106

This blade idler pulley (part number 196106) is for lawn tractors. Blade idler pulley 196106 applies tension to the blade belt, allowing the belt to turn.

Switch-Ign

$14.93

Fix Number: FIX9020864
Manufacturer Part Number: 532193350

This ignition switch has been sourced directly from the original manufacturer and is sold individually (key sold separately). The ignition switch is also sometimes referred to as a starter switch and is enclosed in a plastic housing. A common sign that this part is malfunctioning is if the electric starter is not engaging. For this quick and easy repair, start by making sure the switch is in the off position and the key has been removed. Lift the hood up, locate the steering housing and press the tabs to disengage the old switch. Disconnect the wires and install your new OEM ignition switch.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

MICHELE h from ARGYLE, NY

Barely turns over to start, dead battery

Disconnected battery, unplugged key switch, using screwdriver removed old switch and replaced with new switch. Removed battery cables from old solenoid and replaced with the new one. End results still doesn't turn over enough to start it. Failed repairs Read more...

Jonsered Parts

Popular Jonsered Parts

Installation Instructions

Installation Instructions

Appliance Type

Popular Jonsered Models

Jonsered Parts

Start With Your Model Number

Popular Jonsered Parts

Installation Instructions

Installation Instructions

Appliance Type

Popular Jonsered Models