Dirt Devil Parts

Fix Number

FIX10473218

Manufacturer Part Number

RO-801711

This is a high-quality component which is made for Dirt Devil and Royal vacuums. It is supplied from the original equipment manufacturer. The cap is utilized to secure the wheel on the axle. If the cap is damaged or missing, this part will provide an identical replacement. Make sure to check the diagrams for your specific model for the correct installation of the new component. This high-quality wheel retainer cap is made of durable material and is sold as an individual item. Replacing it is a simple task that should only require pliers.

Fix Number

FIX10334544

Manufacturer Part Number

RO-540310

This is a genuine Dirt Devil upright vacuum belt. It fits vacuums that use a Style 4 or Style 5 belt. This is a flat belt which is used to transfer motion from the drive shaft to the brushroll. Th brushroll spins inside the suction nozzle in order to agitate the fibers of carpet or upholstery. This loosens dirt for a thorough clean. Note that the old belt may seem larger then the replacement belt because they get stretched out over time. One belt is included per package.

★★★★★

★★★★★

1 Review

Fix Number

FIX10334472

Manufacturer Part Number

RO-157260P

Genuine Dirt Devil Style 1 Belt. It is sold in a pack of two. It is used on the Dirt Devil models listed below. Depending on how often this vacuum is used, you should replace your belts every 3 to 6 months.

Fix Number

FIX10334598

Manufacturer Part Number

RO-720310P

Genuine Dirt Devil Style 4/5 Belt fits all Featherlite Uprights that use paper bags, all Swivel Glide Uprights that use paper bags, and all Dirt Devil Vision Uprights. Replace your belts every 3 to 6 months.

Fix Number

FIX10334617

Manufacturer Part Number

RO-790710

This is a genuine item that is supplied by the original equipment manufacturer for use with Dirt Devil and Royal carpet cleaners. It is an identical replacement for a missing or damaged cap that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable plastic and is sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX10334638

Manufacturer Part Number

RO-860140P

These are genuine manufacturer sourced replacement belts used on upright vacuums. It helps to drive the brushroll assembly. These belts are made out of rubber. Includes two (2) belts per order. It is recommended to replace these belts every 6 months to ensure optimum performance. You would need a screwdriver to complete a repair. • First remove nozzle guard • Slide belt off motor shaft • Lift and remove brushroll • Dispose of old belt • Place belt on motor shaft, then slip brushroll through belt • With belt in place, pull and slide brushroll into nozzle • Reattach nozzle guard

Fix Number

FIX10334439

Manufacturer Part Number

H-38528040

Genuine OEM replacement part, this item is sold individually. The purpose of this belt is to rotate the Brush Roll on the vacuum models shown below. This belt is Style 23. Depending on the model you have, it can be installed in different ways. If possible look how the old belt was installed so it will be easier to replace it.

Fix Number

FIX10334810

Manufacturer Part Number

RO-LV1110

This replacement F-22 filter is a high quality OEM item that is specially produced for Dirt Devil vacuums. It is an authentic part that helps to filter out dust and debris from the air that goes in the engine. Replacing this pleated paper filter is a simple task that does not require any tools, take out the old filter and replace it with a new one.

Fix Number

FIX10334665

Manufacturer Part Number

RO-880262

This belt lifter is an OEM part direct from the original manufacturer for use with Dirt Devil and Royal hand vacuums. This belt lifter is used to adjust the belt on the brush roll and motor shaft. This part is made of black plastic and is sold as an individual replacement part.

Fix Number

FIX10473206

Manufacturer Part Number

RO-672260

This is a belt for your vacuum. It rotates the brush roll assembly that is used to collect dust, hair, and other small debris. The belt is located and installed in various places, depending on your model. Because it is constantly working when your vacuum is running, the belt is a commonly replaced part. It is sold individually, however, we recommend buy two at once to keep an extra on hand.