Cub Cadet Parts

★★★★★

★★★★★

4 Reviews

Fix Number

FIX9988561

Manufacturer Part Number

647-04271-0637

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Craftsman lawn mowers. The grass bag frame supports and hold the grass bag in place, while it is collecting grass clippings. To install or replace the grass bag frame requires no tools. This part is made of metal and is sold individually.

Fix Number

FIX9092936

Manufacturer Part Number

712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX9903219

Manufacturer Part Number

17211-ZL8-023

To ensure your engine is protected, it is vital that the air filter is inspected regularly and replaced according to the manufacturer recommendations. This filter helps to prevent dirt and dust from making its way into the carburetor and damaging the engine. If the engine is not functioning as it should, this should be one of the first parts you check. To inspect the filter, you will need to remove the air cleaner cover, and lift the filter out of place to remove.

Fix Number

FIX9899150

Manufacturer Part Number

16228-ZL8-000

This is a carburetor gasket and is sold individually. If your engine is running rough, it could be due to a worn or damaged gasket. The gasket is meant to provide an air tight seal, to help protect the engine. This gasket should be replaced when repairing the carburetor. When removing this part, it is advised to clean the surfaces around the carburetor gasket before installing the new one.

Fix Number

FIX9118299

Manufacturer Part Number

753-06183

This is an authentically sourced fuel tank assembly, including the fuel lines, fuel cap, fuel filter, and screws needed for assembly. This fuel tank assembly is for trimmers, and is where the fuel is filtered and stored for use with the engine. Due to its constant contact with fuel, especially if fuel has been left it in for extended periods of time, it may crack, in which case it should be replaced immediately. Leaking gas is very dangerous, so it is important that it get fixed quickly. Before beginning this repair, drain the gas from the tank before installing the new one.

Fix Number

FIX9110822

Manufacturer Part Number

738-04124A

Designed for use in MTD, Yard Machine, Troy-Bilt, Yard-Man, and Craftsman machines, this OEM approved Shear Pin fits a variety of models. For full compatibility, please see the "Model Cross Reference List" below. This is a shear pin for your lawn and garden equipment, most commonly your snow blower. It is designed to snap if your auger gets jammed or clogged, to protect your snow blower from further damage. Because this part is meant to snap at a certain point of pressure, it is a commonly replaced part in snow blowers. Consequently, we recommend keeping a spare on hand. This Shear Pin is approximately 1.75" long, and is sold individually.

Fix Number

FIX17055954

Manufacturer Part Number

736-0524B-1

This is a bell blade support, also known as a bell spacer, for your lawn mower. It is fitted between the bottom of the blade, and the blade bolt. This part provides support for the blade. It is made of metal to ensure a long life. If there is visible damage or wear, replace this part.

Fix Number

FIX9119300

Manufacturer Part Number

753-06190

A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.

Fix Number

FIX9899099

Manufacturer Part Number

16221-883-800

Fix Number

FIX9096195

Manufacturer Part Number

714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.