OEM Amana Wall Oven Parts & Accessories

Light Bulb - 40W

$11.73

Fix Number: FIX884734
Manufacturer Part Number: 8009

This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and unscrew by hand to replace. It is designed to tolerate extreme temperatures, which is why it is commonly used to light the inside of refrigerators and ovens. Depending on the appliance and location of the bulb, disconnecting the power is recommended. This bulb is sold individually.

Installation Instructions

Helen from Quincy, MA

lightbulb in refrigerator went out

Removed plastic shield on top of refrigerator. Removed old bulb.. Replaced new bulb. Reinstalled plastic shield. Voila! Read more...

Watch the install video

Long Oven Sensor

$34.75

★★★★★

1 Review

Fix Number: FIX1570174
Manufacturer Part Number: 12001656

This is a factory-certified oven sensor kit with two harness adapters. Its purpose is to sense the temperature inside the oven. Replacing this part can fix an oven that is not reaching the proper temperature (too hot or not hot enough), not heating evenly, or an oven that will not start. To access this part, you will need access to the back of the range. Use a Phillips screwdriver to remove the screws on the access panel. Once the access panel is removed, you will notice a hole on the right side of the oven where the temperature sensor comes out of the oven. You will need to unplug the wire harness, and then open the oven door, locate it in the upper left corner, and remove the screws holding the temperature sensor in place. Pull the sensor out of the back of the oven, and replace it with your new part.

Fixes these symptoms

Door won’t open after self cleaning cycle
Element will not heat
Little to no heat when baking
See more...

Installation Instructions

Michael from Pearl River, NY

Oven did not heat up

Removed the oven door, removed existing screws. Pulled wire carefully out of opening, unclip connection. Reattached connection screwed back new sensor attached oven door finished. Read more...

Thermal Fuse

$32.54

Fix Number: FIX11756138
Manufacturer Part Number: WPW10545255

This thermal fuse is a manufacturer-approved replacement part for your oven. It is common for the oven to lose power after completing a self-cleaning cycle, and the thermal fuse is often at fault. Replacing the blown fuse is a fairly easy repair, and involved removing the top of the oven to swap out the fuse. Make sure to turn off the power source to the oven before beginning this repair.

Fixes these symptoms

Door won’t open after self cleaning cycle
Touchpad does not respond
Will Not Start
See more...

Touch-Up Paint - White

$8.00

Fix Number: FIX385132
Manufacturer Part Number: 72017

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Installation Instructions

Al from Cape Coral, FL

No heat when trying to dry clothes .

Followed instructions on your videos. Everything went as planned and the dryer works like new.... Read more...

Watch the install video

Terminal Block

$34.09

Fix Number: FIX11750972
Manufacturer Part Number: WPW10245259

It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).

Fixes these symptoms

Element will not heat
Little to no heat when baking
Touchpad does not respond
See more...

Watch the install video

Door Hinge

$98.27

★★★★★

2 Reviews

Fix Number: FIX11744215
Manufacturer Part Number: WP74008014

If your oven door is not opening or closing easily, there may be an issue with the door hinge. The hinge uses spring tension to allow the door to stay open at an angle instead of dropping open. This genuine OEM hinge can be used on either the left or righthand side of the door, and measures approximately 20.5 inches long. This part is sold individually, however we recommend replacing both hinges at the same time, as they can wear out a similar rate.

Fixes these symptoms

Door won’t close
See more...

Installation Instructions

Carolyn J. from Oswego, KS

Oven door Hinge was broke...Door would just fall open

Watched the video on the repair you supplied...gave us confidence to make the repair. As easy as the video shows. We went ahead and bought 2 hinges and replaced both sides, since we had it apart...We, however, took the opportunity to take the door completely apart and clean it very good. Went back together easy. The new parts fit perfectly and my oven looks and works like it is brand new..New light bulb was a snap too. So glad I found this company....fast shipping too. Will always look here first in the future. Read more...

Flat Style Oven Igniter

$58.40

Fix Number: FIX387058
Manufacturer Part Number: 786324

This is an authentic OEM replacement part.?This flat style over igniter is commonly used in ranges and wall ovens. This igniter is specifically used to ignite the broil element. The igniter pulls current from the ignition circuit, the more current it pulls the hotter the element gets. When it starts to glow and it reaches a certain temperature the gas valve will open and this igniter will create the spark needed to light the gas. When you are installing this replacement part you will need to reuse the original mounting bracket, and you will need a screwdriver. This ignitor is approximately 7.5 inches in length, it is flat in style, it has a 5-1/4-inch ceramic block, and it features 12-inch wire leads. Be careful not to touch the black element as it is very fragile. Before starting this repair make sure you have shut off the gas supply and unplugged the appliance.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Little to no heat when baking
See more...

Installation Instructions

Rex from Naperville, IL

Oven took a long time to preheat

Replaced the "bake igniter." Removed the old one by first removing the door oven (instructions in the owners manual), then the heat shields at bottom of oven, and then removed the three screws holding the bracket surrounding the igniter. Had to remove metal back of the range (very easy - five or six screws) to access the wire nuts connecting the igniter. Connected new igniter using the same wire nuts, re-taped the wire nuts, and reinstalled everything in reverse order of above. Had it not been for the difficult position of the range, (basically positioned as a "built-in) the time to complete would be about 20 minutes. Read more...