Official Crosley Range Switches

Infinite Burner Switch

$43.86

Fix Number: FIX1145040
Manufacturer Part Number: 316436001

The infinite burner switch is used to control the temperature of the burner element on your stove top. This model is for the larger, eight-inch element. If your burner is not heating up or has uneven temperatures, you should first check with a multimeter to see if the issue is with the element or with the infinite burner switch. If you need to replace the switch, first disconnect the power supply to your range. To change this part, you will need access to the back panel, so you will need to pull the appliance out from the wall. To complete the repair, you will need a pair of needle nose pliers, a number one square head screwdriver, and a Philips screwdriver. The specifications for this genuine OEM part are that the switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp.

Fixes these symptoms

Element will not heat
Little to no heat when broiling
Oven is too hot
See more...

Watch the install video

Infinite Burner Switch - Small Element - 240V

$62.84

Fix Number: FIX1145039
Manufacturer Part Number: 316436000

This switch controls the stove top surface burner.

Fixes these symptoms

Element will not heat
Oven is too hot
Will Not Start
See more...

Watch the install video

Range Infinite Burner Switch - 8 Inch

$57.14

★★★★★

1 Review

Fix Number: FIX11744487
Manufacturer Part Number: WP7403P239-60

This infinite switch for eight inch range burners is almost three inches long. This infinite switch is for 8-inch range burners. When an element is unable to produce any heat on a modern oven, the problem may lie with the infinite switch. This switch is responsible for sending power to the surface elements. Check the element and terminal block to ensure they are working properly. If they are in working order, check the infinite switch at the control panel for any wires that have overheated, or broken terminals to or from the infinite switch. If the infinite switch is damaged or malfunctioning, it will need to be replaced. Remember to unplug your range before beginning this repair.

Fixes these symptoms

Element will not heat
See more...

Watch the install video

Dual surface element switch

$155.72

Fix Number: FIX3504401
Manufacturer Part Number: 316238201

This switch controls the stove top surface burner. This surface element control switch is for ranges. Surface element control switch turns the surface element on and off and controls how much heat the element produces. Unplug the range or shut off the house circuit breaker for the range before installing this part.

Fixes these symptoms

Element will not heat
See more...

Spark Ignition Switch Assembly with Wire Harness

$69.60

Fix Number: FIX3409148
Manufacturer Part Number: 316580611

Four switches are included with the assembly.

Fixes these symptoms

Will Not Start
See more...

Infinite Burner Switch - 8" - 240V

$61.18

Fix Number: FIX1529262
Manufacturer Part Number: 318293811

This switch controls the stove top surface burner.

Fixes these symptoms

Element will not heat
See more...

Spark Ignition Switches with Wire Harness

$79.15

Fix Number: FIX3409151
Manufacturer Part Number: 316580615

Fixes these symptoms

Will Not Start
See more...

Watch the install video

Dual Surface Burner Switch

$90.75

Fix Number: FIX11744018
Manufacturer Part Number: WP74003122

This part has been updated by the manufacturer. This updated part now has 7 wire terminals instead of 5. The terminals are all labeled, however, the new switch needs to be tested before connecting the pilot lamp wire (P). To test the new switch: 1) Connect the Line Wires (L1 and L2), connect the Load Wires (H1 and H2). 2) Do not connect the pilot lamp (P) wire yet. 3) Reconnect the power to the range and turn on the new switch and one other switch. 4) Connect the leads of a volt meter on L1 of the new switch and P of the other switch you turned on. 5) If the volt meter reads 220V, the L1 and L2 wires on the new switch must be reveresed. 6) Disconnect power, reverse Line Wires if needed and connect the P wire. 7) Reconnect power to the range after reassembly.

Fixes these symptoms