OEM Frigidaire Range Hood Parts & Accessories

Watch the install video

$23.10

Oven Bake Element

★★★★★

10 Reviews

Fix Number FIX438018

Manufacturer Part Number 316075103

This genuine OEM bake element is located on the bottom of the oven cavity to supply heat for baking. The approximate size is 19-1/2 inches wide by 18-1/2 inches long and has 3-1/2 inch inserts. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. Please remember to disconnect the power to your oven before you start your repair. Next, remove the 2 screws securing the old element, pull it out, and discard. Connect the new element prongs where the old element fit and screw it back in place. This is a very simple repair that anyone can do.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

Installation Instructions

Werkheiser from Saylorsburg, PA

Bake element broke

Extremely easy. I unscrewed two screws and pulled out old element and plugged in the new one. Pushed back in and screwed the screws back in. That's it Read more...

Watch the install video

$43.86

Infinite Burner Switch

★★★★★

1 Review

Fix Number FIX1145040

Manufacturer Part Number 316436001

The infinite burner switch is used to control the temperature of the burner element on your stove top. This model is for the larger, eight-inch element. If your burner is not heating up or has uneven temperatures, you should first check with a multimeter to see if the issue is with the element or with the infinite burner switch. If you need to replace the switch, first disconnect the power supply to your range. To change this part, you will need access to the back panel, so you will need to pull the appliance out from the wall. To complete the repair, you will need a pair of needle nose pliers, a number one square head screwdriver, and a Philips screwdriver. The specifications for this genuine OEM part are that the switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp.

Fixes these symptoms

Element will not heat
Little to no heat when broiling
Oven is too hot
See more...

Installation Instructions

Dan from RICEBORO, GA

8" burner on stove would go to high heat even if set on low.

Pulled stove out.
Disconnected plug.
Removed back upper cover (6 screws).
Removed upper and lower wiring harness (quite easy).
Removed burner knob (on front of stove), removed two screws holding infinite switch.
Removed old switch, replaced with new.
Replaced screws at front.
Replaced burner knob.
Reinstalled back plate, plug in, good to go. Read more...

Watch the install video

$19.73

Light Bulb

Fix Number FIX12751166

Manufacturer Part Number 316538904

Clear, 120 Volt, 40 Watt.

Installation Instructions

Chris from Lillington, NC

Broken bake element & light bulb

Turned of the power at the fuse box as the oven was hard wired to the electrical source and then removed the old element via the screws at the back of the oven. Disconnected the wires from the element and then reconnected those to the new element. Screwed the element base to the back wall of the oven and then replaced the light bulb. Read more...

$47.25

Temperature Sensor

Fix Number FIX1528542

Manufacturer Part Number 316490000

If your oven has little to no heat, is not heating evenly, or is reaching too high a temperature, there may be a problem with your oven probe. This probe, also known as an oven temperature sensor or a range probe, is found in the cavity of the oven and is used to detect the temperature within there. The probe helps the oven to maintain the desired temperature by communicating with the motherboard in the oven. You can use a multimeter to test if the probe is faulty, and if so, the probe should be replaced. Please be sure to disconnect the power supply to your range before beginning this repair, as you will be working with electrical components. The tools required to complete this repair are a quarter-inch nut driver and a pair of needle nose pliers.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Paul from Chicopee, MA

Bake element not heating

First tried heat probe replacement but bake element still not heating. Replaced control board solving problem. Easy installation. Read more...

Watch the install video

$9.37

Main Terminal Block Kit

Fix Number FIX471605

Manufacturer Part Number 5304409888

Terminal blocks (also called terminal boards or strips) provide a convenient means of connecting individual electrical wires.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

$48.85

PROBE

Fix Number FIX16745361

Manufacturer Part Number 5304525427

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Watch the install video

$62.84

Infinite Burner Switch - Small Element - 240V

Fix Number FIX1145039

Manufacturer Part Number 316436000

This switch controls the stove top surface burner.

Fixes these symptoms

Element will not heat
Oven is too hot
Will Not Start
See more...

Installation Instructions

Randy from Gray Court, SC

Stove top burner uncontrollable

In plunged stove, removed upper back panel, removed knob for eye, removed two screws for switch, replace switch, reassembled stove, less then 5 min of work Read more...

$121.67

Oven Rack

Fix Number FIX1765356

Manufacturer Part Number 316496201

This is a replacement rack for your oven. The oven rack fits into grooves on the side of the oven wall, and acts as a shelf that you can place food items on when you want to cook them in the oven. This rack is 24 inches wide and 16 inches long, and is chrome in color. Occasionally, the rack will become warped or distressed, or it may be missing from your oven. In these cases, it will need to be replaced. To replace the rack, simply slide out the old rack and replace it with the new one.

$322.75

GLASS

★★★★★

1 Review

Fix Number FIX12175974

Manufacturer Part Number 316452758

This oven door outer panel is for ranges Oven door outer panel covers the outermost part of the oven door. Wait until the surface is cool to the touch before starting the repair. Wear work gloves to protect your hands. Caution: The oven door is heavy, so you might need two people to safely lift it off the oven frame for servicing.

Watch the install video

$69.92

ELEMENT

Fix Number FIX16763418

Manufacturer Part Number 5304533520

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

Chris from Dayville, CT

Burner would not turn on/ hot surface light always on

My issue ended up being more than just the burner, but it was all an easy repair. For about a year the "hot surface" light would stay on long after the cooktop had cooled. Then one day the burner just stopped working. (More on that later but my inexperience led me to just order the burner assuming that was the only problem) The burner I removed was not necessarily bad but the temp sensing element which was made of glass had shattered presumably the reason that light would never turn off. I might have been able to just replace the temp sensing probe but I had the new burner in hand and needed my stove up and running. Two screws hold down the glass surface, then you can raise it just like a car hood. Used a piece of wood to prop it up, there is a brace holding the burners in place. You need to take out the pair to access the burner you want to replace. Make note of the holes everything is screwed/clipped in to so the new one goes in exactly the same. There is a great video on youtube I found when searching for "Frigidaire burner replacement" that was step bystep exactly what i encountered on my repair. Once i got the new burner in I was surprised to find it didn't light. I used an ohm meter to test everything and it all looked good at the burner. I pulled the top back panel behind my controls and found a corroded and broken wire on the controls for that burner. My guess is all that time of that probe being broken caused there to be current through that line and fried the wire. Either way it was a quick splice and the new burner fired right up and has been working great ever since. I was especially happy that the new temp probe was metal and not glass so I hopefully don't run into this problem again. Read more...

Frigidaire Range Hood Parts

Popular Frigidaire Range Hood Parts

Appliance Type

Related Pages

Popular Frigidaire Range Hood Models

Frigidaire Range Hood Parts

Start With Your Model Number

Popular Frigidaire Range Hood Parts

Appliance Type

Related Pages

Popular Frigidaire Range Hood Models