MVWP575GW0 Whirlpool Washer - Instructions

Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

Unplug unit. Remove back panel. Disconnect drain hose using pliers to squeeze hose clamp. Tilt washer forward to access drain pump. Remove three screws on the pump. Unplug wire connector. Install new pump. Plug in the wiring connector. Reconnect hose. Reinstall back panel. Super easy fix!

First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Cogs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .

I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

The repair was very simple. I removed the agitator cap with a small screw driver, removed the retainer screw with a socket set tool. I removed the top agitator, lifted the cam and removed the old worn directional cogs installed the new ones. I reassembled the agitator. All of 10 minutes.... Very easy

Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.

replaced missing screw and pad and now machine works perfectly

Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.

After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agitator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!

removed the agitator and melted the retaining clips to loosen the retainer cover for the cogs. went simple after that.