CAW35114GW1 Whirlpool Washer - Instructions

Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.

Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes

Removed the fabric softener cup, remove plastic cap that prevents fabric softener from going into the agitator column, removed screw, replaced dog teeth and cap that holds them in place, put agitator back together.... Done.

Cleaned inners of the dispenser and snapped on new part

Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.

Trying to follow the instructions according to the video was easy enough until the part where I had to remove the control panel for access to the screws holding the inlet valve. I don't have a putty knife, so I had a bit of trouble trying to remove the panel. I found another way. There are screws on the left and right sides which hold the control panel to the side pieces holding it to the body. If you remove the screws and use a pick or flathead screwdriver to carefully pull up on the tabs below the screws while gently pulling the control panel away, it will easily pop off with a rotational movement. The panel is centered into its location via two plastic pins molded into the side panels, so be aware of them and try to avoid breaking them. They'll help you get the panel properly positioned during reassembly, which is simple. You'll see all this easily if you take the time and look. Don't be in a rush. To reassemble, line up the panel with the plastic pins and rotate it into position. The tabs slide easily into position and lock the panel into place. Just don't forget to reinstall the screws. Removing the panel in this manner added a bit of time to the repair, but not a lot. It's still a fast repair overall. Everything else was exactly like in the video. Well, almost. I had no difficulty whatsoever with sliding the new valve into place. But once the job was done the sounds coming from the washer during the filling stages ceased. Turns out the screens in the inlet valve were getting stopped up with lime.

followed the instructions on the video, very easy install

Per the instructions on the website, I:
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.

Problem is resolved, saved almost $250 by doing it myself!

I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .

Removed softener dispenser, removed part under that to reveal bolt that holds agitator on to washer. Figured out there was more to the problem than just the dog ear things and had to end up getting a whole new agitator. Probably saved us $60 minimum in labor and trip charge and was a piece of cake! Took my husband less than 15 mins. to remove old agitator and put on new one. Geez, I guess I have to do laundry again!

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

I took out the softner dispencer and there is a bolt under tthe the plastic cover,I removed the bolt and the whole assembly came out,then I installed the new one and reinstlled the bolt and plastic cover,and reinserted the liquid softner dispencer.All only took about fifteen min.

popped off the softener cap, removed inner seal cap, removed bolt holding the top agitator and removed top agitator by pulling up. Removed the ring holding the dogs in place. Replaced the dogs and slipped it all back together

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.