WTW4850BW2 Whirlpool Washer - Instructions

The installation was very easy and took me 45 minutes to complete by myself. I put the washer on two cinder blocks and then removed the lid. I started with the suspension rods that were closest to me and they were really easy to exchange. When I got to the rods in the back they were a little more difficult because there was more tension with the new rods installed. I used the old rods to hook and pull the new rods into place and it was overall very easy.

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys

Replaced agitator cog/clutch unit under the softener dispenser. It is the second time I've replaced it in the last 3 years, maybe it has been loaded too heavy, I'll have to have that talk with everyone else on the family who does laundry.

1. Remove Top Cap.
2. Remove Seal Cap.
3. Remove 7/16 Bolt
4. Lift out Old Agitator
5. Put in NEW Agitator
6. Replace 7/16 Bolt
7. Replace Seal Cap
8. Replace Top Cap.
9. Sit back and enjoy your clean clothes

Watched video from partselect and it was on the money. Removed a few screws and tilted the lid. (after unplugging). Pulled it out from wall and tilted machine to have access to bottom. Had grandson reach from underneath and pull the rods out and inserted the new ones. Work great now. My wife is happy and I saved about $600 because I didn't have to buy a new one.

the first order was ordered wrong for me and the part was to big so I had to send it back and order another. The second dispenser was the right one and went on well to the machine. Just had to put it on the machine by hand.

I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%

PS - I put some light lithium grease on the transmission and it’s quieter than it was when new

When to PartSelect Web site, used their trouble shooting guide, Used their advice, which was to replace the actuator. bought and installed the actuator which took around 20 minutes or so. washer started working fine after replacing. Thanks to the website I save a lot of money. Thanks PartSelect

I watched the PartsSelect video. I was hoping for the tub with the slots in the tub mounts, but mine didn't have them, so I had to lay it down on its back. The only thing I did that was not in the video was I placed a 2" thick closed cell foam knee pad I had on hand between the tub and the back of the housing. When I laid it down, the tub was elevated by 2". This made reaching the two rear rods a little easy. It seems that there would be a more robust way to achieve the dampening affect, but I guess this is cost effective.

It's strange that I searched for my issue several times and only saw recommendations to level the washer. It was level. Then one day I ran across the suspension rod resolution. It didn't do it on every load, but after a year of my wife nagging me and threatening to get a new washer, I finally fixed it. The biggest issue is just logistics in a condo hallway and a little leaking water. I also replaced my hoses. Should be in good shape until the next thing.....

Watched a video

First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy

I needed an air impact wrench to remove the single nut. It was stuck on there. Once the Nut. Was removed it was an easy repair. Perfect fit! Just pop it on the shaft and replace the bolt. Since I had my air tools out already I gave it a couple of dugga duggas.

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]