WTW4850BW0 Whirlpool Washer - Instructions

Inserted a straight slot screwdriver into the small opening between the Fabric Softener Dispenser and the Agitator Assembly. Twisting the screwdriver slightly, causes the dispenser to separate from the agitator exposing a 7/8" bolt. Using the proper socket, removing the bolt allows for the removal of the complete agitator assembly. Reverse this process to install the new complete agitator assembly.

I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose

My washer is an Amana He, but the part is made by Whirlpool, I think. I just set the new part on the middle agitator in the washer and pushed it firmly down and it snapped into place. It was amazingly EASY!!!!!!!

Removed the fabric softener cup, remove plastic cap that prevents fabric softener from going into the agitator column, removed screw, replaced dog teeth and cap that holds them in place, put agitator back together.... Done.

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes

Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.

I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

I took out the softner dispencer and there is a bolt under tthe the plastic cover,I removed the bolt and the whole assembly came out,then I installed the new one and reinstlled the bolt and plastic cover,and reinserted the liquid softner dispencer.All only took about fifteen min.

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

popped off the softener cap, removed inner seal cap, removed bolt holding the top agitator and removed top agitator by pulling up. Removed the ring holding the dogs in place. Replaced the dogs and slipped it all back together

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.

First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Cogs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .

remove softener dispenser and one other snap out part then remove on bolt, removed old part (took some coaxing with a screwdriver) glad i ordered the combo part instead of the dogs only as I had to almost destroy the old part to remove it. Installed the new part and my clothes are now once more agitated.