WTW4850BW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jimmy from Pomona, CA
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
washer would not agitate
Watched a video at partselect showing how easy it is to repair the agitator. Ordered the parts, which arrived in about 4 days. it took me about 15 minutes to replace the parts. washer works great. I saved about $200.00 by doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NAPERVILLE, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Agitator moves freely in both directions
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from BROOKLYN, NY
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Making loud noises.
The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hale Center, Texas, TX
- Parts Used:
- WPW10240513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lid would not lock, washer would not run...
Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Armand from WESTPORT, MA
- Parts Used:
- WPW10683603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Water inlet nozzle was stripped and leak
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from HARLINGEN, TX
- Parts Used:
- W10780045
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My tub would hit the sides of the washer during spin cycle.
Followed youtube video. The repair was easy and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from GRAIN VALLEY, MO
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
squeal and chirping while in risne / spin mode
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phillip from worcester, MA
- Parts Used:
- WP3951632
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
would not move clothes
Took the cup for the clothes softner out, just pulls out, took plastic seal out, just pulls out, took the socket set,with an exstention, unscrewed the bolt & pulled out the agitator. easy. Reverse the process in putting the agitator back. P.S. Right hand thread.
.
.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from ARLINGTON, TX
- Parts Used:
- WPW10683603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Hot water valve would barely open - take 35 mins to fill washer
Pull the washer out from wall
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips
Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips
Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from HOPE MILLS, NC
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer wouldn't start - Flashing Lid Light
I checked out the reviews and the recommendation of these "professionals", replaced the part easy enough when it came in. However, it didn't solve the problem. Got an actual professional to come in and see what the problem was, and they determined that gear oil was being leaked and it wasn't worth replacing.
Tried to get a refund and return the part. Was told absolutely not. The money back guarantee is a lie.
Tried to get a refund and return the part. Was told absolutely not. The money back guarantee is a lie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HICKORY, NC
- Parts Used:
- WP8536939
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The main knob insert snapped.
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTI from NEWPORT NEWS, VA
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Making Alot Of Nosie While Washing
First I removed the fabric softner dispenser. Then I removed cap took screw out removed agitator asseembly put new one in then I put screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LADD from ARCADIA, FL
- Parts Used:
- W10780045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
When the washer would go into spin cycle it sounded like the drum was banging all four sides of the washer.
Unplugged from power, unhooked water lines.Then removed back cover and control panel and top set to the side. Rear rods very easy to do by yourself after those where done have help and tip it backwards and change out the front 2 then reassembled and hooked back up and tested. Everything worked like brand new !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PRECIOUS from LAKE CITY, FL
- Parts Used:
- W10780045
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer shaking and banging loudly
I was able to look up the issue on Youtube and watched a few videos and was able to complete the repair with help of my daughter. It was little hard to do but you do need gloves with a good grip when taking the rods out of the washer, but putting the new ones in was very easy.
Once I replaced the suspension rods, there was a little shaking but not like before. Very quiet now, no crazy loud banging
Once I replaced the suspension rods, there was a little shaking but not like before. Very quiet now, no crazy loud banging
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REED from BUCHANAN, NY
- Parts Used:
- WPW10276397
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Wouldn’t drain pump made loud noise
Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues
Was this instruction helpful to you?
Thank you for voting!