WTW4850BW1 Whirlpool Washer - Instructions

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

I unscrewed the agitator and pulled it out. Then took out the old agitator cam kit and put in the new one.

Took the Cover off and installed belt.

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

Removed the fabric softener cup, remove plastic cap that prevents fabric softener from going into the agitator column, removed screw, replaced dog teeth and cap that holds them in place, put agitator back together.... Done.

Removed softener dispenser, removed part under that to reveal bolt that holds agitator on to washer. Figured out there was more to the problem than just the dog ear things and had to end up getting a whole new agitator. Probably saved us $60 minimum in labor and trip charge and was a piece of cake! Took my husband less than 15 mins. to remove old agitator and put on new one. Geez, I guess I have to do laundry again!

I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

Tip the washer on its back remove the agitator install new one under 15 minutes

My washer is an Amana He, but the part is made by Whirlpool, I think. I just set the new part on the middle agitator in the washer and pushed it firmly down and it snapped into place. It was amazingly EASY!!!!!!!

I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose

I just drained the washer and unscrewed the 3 screws unhooked the hose clamp and installed the new one attached the hose and hose clip. Really easy. Took longer to try up water in floor than installing.