7MWTW1700EM0 Whirlpool Washer - Instructions

I removed dispenser for softener, then pulled cap inside upper agitator, I was able to get my fingers in the grips and pull firmly to unseat it. (disgard o-ring it comes with the repair kit). I then removed the bolt from center and grabbed the bottom of the lower agitator and gave it a good tug to release the whole unit. If that don't work you can get a flat tip screwdriver between the two sections and pry up slightly. Once it was all loose I removed the upper assembly taking care to to remember how all the pieces were assembled. replaced everything in the same order and when it came time to reinstall the inner cap and seal I made sure I put the cap in straight. Also if the seal doesn't cooperate you can use a little liquid soap to lubricate it. you dont want to use grease because it could possibly get on the clothes (the softener sits in there)! You can use the tip of the screwdriver to tuck the oring in if that doesn't work but be very careful

Removed bolt holding top of agitator, removed top of agitator. Replaced parts. Reinstalled agitator. An old machine now works like a new model.

Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.

I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.

Exactly as shown in your video

Tightened up the pulley as the video showed me that might be the issue.

After disconnecting water lines and power, tip machine onto its back. The actuator is located under the drum. Remove the cover over the motor/ drive belt. Actuator is located by the transmission and held on by several screws. Unplug the wiring harness and remove three screws with Phillips screwdriver. Install new actuator..

I watched the PartsSelect video. I was hoping for the tub with the slots in the tub mounts, but mine didn't have them, so I had to lay it down on its back. The only thing I did that was not in the video was I placed a 2" thick closed cell foam knee pad I had on hand between the tub and the back of the housing. When I laid it down, the tub was elevated by 2". This made reaching the two rear rods a little easy. It seems that there would be a more robust way to achieve the dampening affect, but I guess this is cost effective.

It's strange that I searched for my issue several times and only saw recommendations to level the washer. It was level. Then one day I ran across the suspension rod resolution. It didn't do it on every load, but after a year of my wife nagging me and threatening to get a new washer, I finally fixed it. The biggest issue is just logistics in a condo hallway and a little leaking water. I also replaced my hoses. Should be in good shape until the next thing.....

was really simple like others before me described. Removed cap to excess recessed bolt. Once that was out of the way pulled up gently on agitator and disassembled the agitator from base. Actually repair only took about 8 minutes. Working like new again and that keeps everybody happy! Thanks again.

popped off softener cap, easy. Pulled out clear plastic sealer, removed nut holding agitator in, pulled out agitator. Removed cam holder, new cam bearing etc in, reverse removal done, piece of cake.

Had no problem. The instructions included with the repair parts were very easy to follow and even specified the tools to use. I had it done, back on the washer and washing clothes in about a half an hour. The down side(no fault of the parts) was that the entire pump system went out on the second load and we wound up with a new Whirpool washer, since repairs were more than the machine was worth. Thanks Parts select for your help. I plan to search your net for more products. Fixing things from engines to microswitches is a hobby for me.

Pushed the new one into place. No tools, no fuss and very little swearing involved. Clogg was caused by erroneously pouring the liquid detergent into the very handy opening reserved for fabric softener. I'd love to say my wife did that, but.... no, it was me. NOW, the real story. I ordered the part via the web at 10:00 a.m. It was delivered to me at 9:30 a.m. the next morning via Fed Ex. Wow! Great job at PartSelect.

I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.

Remove softener dispencer, use flat tip screw driver to remove agitator cap, there is a slot, insert flat tip screw driver and pry up, once removed you will see the damaged dogs or cogs, use 3/8 drive ratchet with 10 or 12 inch extention and if memory serves me correct a 9/16 socket, loosen bolt and remove top agitator, there is a thrust washer between bottom and top agitator, it comes in the kit, use a little grease preferrably water resistant grease on top of washer, replace top agitator then the plastic device that the cog are inserted into and tighten bolt, put agitator cover back on with a gentle slap of the palm and reinstall softener dispencer, you are done and cloths will agitate properly again, fairly easy job and washer agitator works like new, great kit, would reccomend.

took off the soap dispenser, removed the agitator using a 7/16" socket with an extension. replaced the old top agitator dogs and retaining ring with new ones, re-installed top agitator on bottom, thenput whole assembly back shaft, dropped in bold and tightened. whole experience was fast and simple. the parts came fast and where a perfect fit.