2DWTW4845EW1 Whirlpool Washer - Instructions

I removed the softener cup from the top of the agitator unit. The auger works separately from the bottom agitator. Remove the cap from down in the auger. There is a 7/16" bolt that holds the Auger and agitator to the center shaft. Loosen that bolt with a 7/16" socket on an extension from the ratchet wrench, and remove it from the bushing- I used a magnet. You will need to hold the agitator to loosen the bolt. Save that bolt. You will need it later. The entire agitator and auger can be lifted as a unit straight up out of the washer tub. There is a plastic bushing in the replacement kit. Slide it down over the center shaft with the small tabs up, then apply some Vaseline to the tabs as a lubricant. The new agitator can now be slipped down over the center shaft and seated on the bushing. Place the top auger onto the shaft down on to the agitator. Next, assemble the top bushing by placing the four cogs into the slots with the small pegs. The cogs must have the side with the raised area on the top of the assembly. Next push the plastic keeper down over the center of the bushing to hold the cogs in place and push it down to secure the cogs. Place this assembly into center shaft and line up the four rectangular holes in the top bushing with the four plastic prongs below. The top bushing assembly may be pushed down and secured by the four upright pegs below. If there are plastic tabs obstructing the rectangular holes in the top bushing , you can put the bolt back into the center hole and carefully tighten it down making sure the four holes align with the four pegs below. Tighten until the top bushing is securely in place. You will need to hold the lower agitator while you tighten the bolt with the socket wrench. Replace cap over the top bushing, then the softener cup into the top of the agitator assembly. The job is complete.

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

Removed old agitator and determined teeth in center were worn down. Purchased new upper agitator assembly and repair kit. It now works like a new washer. (NOTE: It wasn't until after I did the repair that I heard 15 years is quite old for a washer. But it cost me $40 to repair compared to $500 to replace. I hope it lasts another 15 years!)

Ordered the agitator repair kit and it came very fast.. Followed the instructions, the kit had all the parts needed.. Took around 30 minutes, but some of that was scraping the built up scale from the agitator itself, you might not have to do that.. Easy job.. Agitator now works like new.. Very Happy, and so is my wife, the kids looked and said, "Hey,my jeans go down to the bottom now, cool..!!"

I simply watched the brief video supplied on both the page as well as my emailed receipt and performed the steps as directed. There were no deviations required... it was exactly how the video described it. Honestly, I expected a more lengthy and complicated repair!

Inserted a straight slot screwdriver into the small opening between the Fabric Softener Dispenser and the Agitator Assembly. Twisting the screwdriver slightly, causes the dispenser to separate from the agitator exposing a 7/8" bolt. Using the proper socket, removing the bolt allows for the removal of the complete agitator assembly. Reverse this process to install the new complete agitator assembly.

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

I removed the fabric softener dispenser atop the agitator. I twisted and pulled out the plug inside the agitator. Using a socket on an extended wrench, I removed the single nut inside the agitator (keep the agitator from turning with a large screwdriver, etc. and turn the nut counter-clockwise to remove). The agitator came out, and I removed all of the cam parts. I cleaned all of the old parts with bleach and water. Reinstalling the new parts was simple and straightforward as indicated in the illustrated instructions. Now it works great!

I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .

Gravy replacement! I pulled out softner dispenser,
undid the one bolt securing the agitator assembly, and removed the top half of the agitator. the cam assembly tapped out. I replaced the bolt so I could still use the machine while the parts were on the way. When the part arrived (36 hours later with 3-5 days expected) I removed the bolt again and followed the simple instructions to replace the cam. Saved a ton on repair costs!

I am a maintenance mechanic and was very easy for me. I just loose i screw 10mm took out old parts put new parts in and it was ready to go again.

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Cogs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .

Popped of lid on agitator and stuck the dispenser in. Fit perfect, works like it should. Thank you for getting me the right size part!