2DWTW4845EW1 Whirlpool Washer - Instructions

1. Remove Top Cap.
2. Remove Seal Cap.
3. Remove 7/16 Bolt
4. Lift out Old Agitator
5. Put in NEW Agitator
6. Replace 7/16 Bolt
7. Replace Seal Cap
8. Replace Top Cap.
9. Sit back and enjoy your clean clothes

the first order was ordered wrong for me and the part was to big so I had to send it back and order another. The second dispenser was the right one and went on well to the machine. Just had to put it on the machine by hand.

Watched video from partselect and it was on the money. Removed a few screws and tilted the lid. (after unplugging). Pulled it out from wall and tilted machine to have access to bottom. Had grandson reach from underneath and pull the rods out and inserted the new ones. Work great now. My wife is happy and I saved about $600 because I didn't have to buy a new one.

I did the repair just as the video showed, and had no problems at all.
the hardest thing I had to do was to move the washer out to where I could get to the back of the machine.
Due to the help of the sales rep and the video the repair was very easy

Thanks
Louis

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

When to PartSelect Web site, used their trouble shooting guide, Used their advice, which was to replace the actuator. bought and installed the actuator which took around 20 minutes or so. washer started working fine after replacing. Thanks to the website I save a lot of money. Thanks PartSelect

Exactly as shown in your video

I watched the PartsSelect video. I was hoping for the tub with the slots in the tub mounts, but mine didn't have them, so I had to lay it down on its back. The only thing I did that was not in the video was I placed a 2" thick closed cell foam knee pad I had on hand between the tub and the back of the housing. When I laid it down, the tub was elevated by 2". This made reaching the two rear rods a little easy. It seems that there would be a more robust way to achieve the dampening affect, but I guess this is cost effective.

It's strange that I searched for my issue several times and only saw recommendations to level the washer. It was level. Then one day I ran across the suspension rod resolution. It didn't do it on every load, but after a year of my wife nagging me and threatening to get a new washer, I finally fixed it. The biggest issue is just logistics in a condo hallway and a little leaking water. I also replaced my hoses. Should be in good shape until the next thing.....

Had to clean debris on metal drive shaft splines in orderv forvnew lower agiitator to seat properly. Install upper agitator and parts then reinsert bolt in upper agitator. Install cap and o-ring, fabric softner dispenser and test for proper operation.

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]

I needed an air impact wrench to remove the single nut. It was stuck on there. Once the Nut. Was removed it was an easy repair. Perfect fit! Just pop it on the shaft and replace the bolt. Since I had my air tools out already I gave it a couple of dugga duggas.

I unscrewed the top panel of the washer. I lifted up the top and used the pint scrapper to loosen up the lid switch and slid it out. I pulled the switch wiring harness out of the rear top of the washer. I slid the new lid switch and wiring harness back through the opening and secured the switch in place. Screwed it back in place. Took less than 15 minutes. I followed the instructions on the video, easy peasy lemon squeezy.

There are a lot of complaints, with these new energy efficient washers, no matter the brand, on the amount of water that is being used, and not properly washing your cloths, while in the wash cycle.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.

I removed dispenser for softener, then pulled cap inside upper agitator, I was able to get my fingers in the grips and pull firmly to unseat it. (disgard o-ring it comes with the repair kit). I then removed the bolt from center and grabbed the bottom of the lower agitator and gave it a good tug to release the whole unit. If that don't work you can get a flat tip screwdriver between the two sections and pry up slightly. Once it was all loose I removed the upper assembly taking care to to remember how all the pieces were assembled. replaced everything in the same order and when it came time to reinstall the inner cap and seal I made sure I put the cap in straight. Also if the seal doesn't cooperate you can use a little liquid soap to lubricate it. you dont want to use grease because it could possibly get on the clothes (the softener sits in there)! You can use the tip of the screwdriver to tuck the oring in if that doesn't work but be very careful

Took off water softener from top of agitator. Pulled up and removed cap with O-ring that covered bolt that held agitator in place.then pulled briskly up on entire agitator from the bottom to remove agitator from machine.After that I put my feet on bottom of agitator and then pulled up on top part to separate the two pieces. After that just follow instruction sheets for parts replacement and then reverse steps to reassemble.