2DWTW4705EW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from Berkley, MI
- Parts Used:
- 63580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No fabric softener dispenser
Take out cap and replace with new cup
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from Cato, WI
- Parts Used:
- 63580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My washer did not come with the fabric softener dispenser
Easy as ONE TWO not even a THREE. Just pulled off the cap on top the agitator and dropped in the dispenser. Gave it a little push to seat it and done. Sure beats the softener ball.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roy from mcdonough, GA
- Parts Used:
- 63580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no softener dispenser
Installed cup dispenser and started the laundry
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rennel J from Rosamond, CA
- Parts Used:
- 63580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fabric Softener Dispenser won't dispense softerner.
Very easy. Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Palm Desert, CA
- Parts Used:
- 63580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed fabric softener dispenser.
Ordered the part... snapped it in place.... piece of cake!!! The people at Part Select are phenominal.... best customer service I've seen in years...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Port Jervis, NY
- Parts Used:
- WP389140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
No spin on spin cycle
Easy, If your drive block has an open top, it's worn. Look at a picture of a new drive block and compare. If it doesn't match, then you need a new drive block. Note: Also check the drive clutch and clutch liners or pads...they may be worn. In my case it was the drive block this time. So to start, take off the fabric softenner dispenser in the center of the washer. Then pull out the seal. then remove the bolt. and pull off the agitator assembly. after that tap off the lock nut with a punch and hammer or if you have the special spanner wrench tool, use that. Once removed, pull out the inner tub and then pull the drive block off the shaft. Put the new drive block on and reverse the procedure from there. Tap the lock nut tight with the punch and hammer while re-installing. I'm so glad I did this repair. $15 is so much better than just giving in and buying a new washer!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Oviedo, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Missing lid hinge bearing
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Zephyrhills, FL
- Parts Used:
- 63580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Softener started dispensing some black gunk . I cleaned the dispenser but could not get all the gunk out. Decided to install a new dispenser.
Pulled off the old dispenser and popped on the new one. As easy as that. No tools needed. By the way. The service at Partselect was unbelievable. Had the part in about four days. Thanks Partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Faucett, MO
- Parts Used:
- WP63235
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Would not agitate
Plastic "teeth" at top of agitator were completely worn off, allowing the agitator to spin freely on the shaft. Just remove the bolt that connects the agitator to the drive shaft (located under the top cap of the agitator), remove and replace agitator and you're all set.
Was this instruction helpful to you?
Thank you for voting!