1CWTW4815EW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from HILBERT, WI
- Parts Used:
- W11481722
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not Agitate
Tip the washer on its back remove the agitator install new one under 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kerry from WALKERTON, IN
- Parts Used:
- WP63235
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
agitator spin freely by hand. plastic splines striped out
remove cap on top of agitator, use socket with extension to remove bolt. pull up to remove old agitator, reverse order to install new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SIOUX FALLS, SD
- Parts Used:
- 63580
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fabric Softner Dispenser severly pluged
Watched the video on this site on removal and installment Done in less than 5 minutes including cleaning where the dispenser is located
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teamos from Frisco, TX
- Parts Used:
- W10780045
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Washer was rumbling at the spin cycle
Unplugged, removed cold and hot lines, moved out to garage, unscrewed 3 screws on the back, lifted up the top, removed and replaced 1 suspension rod at a time with washer leaning against wall sideways, easy peasy didn’t take no time at all, moved it back in 3 screws back in place hot and cold screwed back in and walla! It worked and has been working flawlesssly..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristy from Lebanon, NJ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was making an awful screeching noise when agitating
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Kalkaska, MI
- Parts Used:
- WP3949550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator broke
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from New Fairfield, CT
- Parts Used:
- W11481722
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Reolaced actuator
1. Unplugged the electrical cord
2. Unscrewed the plastic guard
3. Unscrewed the actuator screws
4 Unplugged the cord.
5. Replaced the olld one with the new one and reversed the order
6. Uprighted the machine
7 Performed trail run with vinegar
2. Unscrewed the plastic guard
3. Unscrewed the actuator screws
4 Unplugged the cord.
5. Replaced the olld one with the new one and reversed the order
6. Uprighted the machine
7 Performed trail run with vinegar
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from CLINTON TWP, MI
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Rinse cycle kept repeating, did not spin clothes
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from PAYSON, AZ
- Parts Used:
- WP63235
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator not working, Striped splines.
replace washer agitator. One bolt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from BRUCETON MLS, WV
- Parts Used:
- WP63235
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The agitator was not spinning.
I took a straight screwdriver and popped off the cap on top of agitator. Then used a ratchet with an extender and loosened and took out the bolt in the agitator. Then pulled the agitator straight up and inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Miami Shores, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rick from SAINT HELEN, MI
- Parts Used:
- 63580
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
installed automatic frabic dispenser new mach didnt have one
removed cover replaced with dispenser
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARNIE from ALBANY, OR
- Parts Used:
- W10756270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Need to return your product
My dryer knobs ended up not only the problem but when i went to use my dryer the heating element wrnt out.... So i need to return your knobs and get my money back please thankyou however i need the correct forms to send them back and i have the original wrapping
Was this instruction helpful to you?
Thank you for voting!