3DWTW3000FW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MARNIE from ALBANY, OR
- Parts Used:
- W10756270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Need to return your product
My dryer knobs ended up not only the problem but when i went to use my dryer the heating element wrnt out.... So i need to return your knobs and get my money back please thankyou however i need the correct forms to send them back and i have the original wrapping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Lake City, FL
- Parts Used:
- W10780045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Walking all over the floor on spin
Unscrewed the back plate,, unscrewed the top section from the back ,tipped the machine back after unlocking the front two suspension rods, put the new ones in with the new locks , tipped the machine forward, took the two back, suspension rods out, put them back in with a new locks put everything back together made sure all the legs were level and recalibrated the machine, which is take dial turn counterclockwise a turn stop on this machine at the regular pointer. Go back one go forward three back one you’ll see all the lights blinking turn to the light that has rinse and hit the start button. It will recalibrate and everything is working fine thank you all they were better rods than what I had ordered. One time before online. These appeared to be the original ones. Which are made better so make sure you use them. Thanks you saved me 600 bucks.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica L from Junction City, KS
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The seal in the upper agitator cap broke
I just unscrewed the top agitator cap and slid the o-ring on and put it back. Done in seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Troutman, NC
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Cogs were stripped out of upper agitator.
Purchased complete agitator for ease of repair. Part came ready to remove broken agitator and replace with new agitator. Pull off top fabric soft dispenser, pull out filer at bottom of dispenser, remove 7/16" bolt from center, pull off complete agitator and replace with new agitator and replace 7/16" bolt, filter and top dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Gallatin, TN
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Top part of agitator not working.
Removed the nut in center of agitator, removed agitator, installed new agitator. Extremely easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Douglasville, GA
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Agitator was not working properly
First I removed the nut holding the agitator assembly and replace it with the new one. It was a simple process and now my washer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Fitzgerald, GA
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The top part of the agitator would not work.
I took the fabric softer dispenser off then used a socketwrench and took the nut off and replaced the whole agitator in a manner fo less than 15 minutes.easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bellefontaine, OH
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Agitator worked part time.
Removed the old agitator (one bolt, two minutes).
Upon receipt of the new part from Partselect (3 days) set the new agitator in place and reinstalled the bolt (two minutes). So simple
Upon receipt of the new part from Partselect (3 days) set the new agitator in place and reinstalled the bolt (two minutes). So simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Plattevillle, CO
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The agitator was broken, did not clean clothes well.
Removed the cap of the existing agitaor then selected the proper socket with an extension and removed the bolt. The old agitator was removed and the new one installed, nut replaced and tightened. Replaced existing cap.
Actually took more time to take the new agitator out of the box it was delivered in.,
Actually took more time to take the new agitator out of the box it was delivered in.,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Augusta, GA
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Upper part of Agitator kept coming off
First I removed the Softener cap. Then I removed the cap over the bolt. 7/16 socket to remove bolt. Removed old agitator and put in new one. Put bolt back in and reinstall parts taken out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson E. from Albany, OH
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Top of the agitator wouldn't work
Removed fabric softner unit. Removed the seal, and 7/16th nut. Removed unit and replaced with
new.
new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Cortland, NY
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
top half of agitator didn't work
I pulled out the fabric softener despencer took out the plastic cap to expose the retaining bolt. Removed the bolt and pulled out the complete agitater. Put together the top and bottom of the new agitater,set it in, put bolt back in. replaced cap and softener despencer. Took about 15 minutes. recieved the parts in 2 days, great site. thanks John
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Conway, AR
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken Agitator
My husband had no problem putting the new agiator together, took old one out and put the new one in, works like a charm.
Linda Palmer
Linda Palmer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Chicago, IL
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The top part of the agitator was broken (loose).
The 5 minutes installion required a 1/2 inch socket with an extensin bar to remove 1 screw.
Was this instruction helpful to you?
Thank you for voting!