7MGHW9400PW0 Whirlpool Washer - Instructions

I took off the front lower panel and the top panel. I also removed the door. I used the screwdriver to remove the first spring and then loosed the screw on the second ring that holds the bellow in place.

Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.

place new baffle over slots in drum; move toward back of drum and snap in to place pressing down and moving toward front of drum

Unplugged power cord, turned off both water valves on the wall, Disconnected the water hoses o the back where they are attached to the water inlet valve. Note: there will likely be some water left in the hoses. Then removed top lid of washer (this is a front load washer) by removing the 3 nut screws on the back of the lid and sliding it to the back and lifting off.. Disconnected the small hose that is attached to the water inlet valve by squeezing the hose clamp and sliding the hose off. Removed the 4 wires connected to the water inlet valve (marked each one with a number in order) then removed the Phillips head screw on the back of the machine holding the water inlet valve, sliding the valve to the right, . Removed valve, and replaced with new one, and re-installed by reversing order of removal.

Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.

Easily. 4 Screws. 2 Clamps.

Easiest repair on 2003 front loading washer. This unit cleverly uses star tool machine screws with a hex head so you can pick your favorite tool. Turn off the water supply. Remove the hot and cold hoses at the inlet valve, draining any water into a small bucket. Have a towel for dribbles. *This is a good time to examine the hoses and replace them if they are anything other than perfect. Burst or leaking hoses is the #1 cause of water damage in homes.* Three screws releases the top cover which slides 1/2 inch back and lifts off easily. Remove one screw securing the inlet valve (same size screw as the others). Pull the old inlet valve away from the rear panel for easier access. Remove the 4 wires from the solenoids (they pull straight off but maybe need a little finesse), and re-attach to the new inlet valve. Using pliers, release the hose clamp on the old valve sliding it down a couple of inches, then move the hose to the new valve and reposition the hose clamp. Toss the old inlet valve in the trash, screw the new one in place, replace the top panel, reattach and hand-tighten your hoses, turn on the water, look for any leaks, and go have a three martini lunch with the money and time you saved.

Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.

First I removed the two screws that held the old handle and then replaced the new handle with the same screws.

Inserted new baffle in washer and slide in place.

1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.

Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.

Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good

This was truely easy. All I needed was a flat head screw driver and it was done within five minutes.