6ALSR7244MW0 Whirlpool Washer - Instructions

A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!

The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.

First I removed the fabric softener dispenser. I removed the inner cap seal and agitator retaining bolt. Then I firmly pulled up on the agitator to remove the complete agitator assembly. I replaced the inner cap seal and installed the new agitator bolt with rubber washer. I placed the new agitator assembly on the drive shaft and tightened the bolt. Lastly I installed the inner seal and the fabric softener dispenser. The total time spent was around 10 minutes.

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Had to clean debris on metal drive shaft splines in orderv forvnew lower agiitator to seat properly. Install upper agitator and parts then reinsert bolt in upper agitator. Install cap and o-ring, fabric softner dispenser and test for proper operation.

The only tricky part was figuring out how to get to the part. There were only two screws that seemed likely candidates to pop off the control panel (on the back at the corners). Fortunately for me the obvious answer was the right one...the panel lifted up and the new part went in - very easy.

Removed the screws holding the control panel onto the washer. Removed the switch knob and then the switch (required unlocking a tab and then rotating the switch to remove). Unplugged the wiring connector and the water sensing tube. Replaced the switch in the reverse order and remounted the control panel. Test run proved the washer was working again.

Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

Exactly as shown in your video

I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.

The switch just snapped out of the holding section and the new part was snapped back into its place. He put the top section back on and it worked! Being a woman not knowing anything about repairing machines, I thought it went very well. I just googled my problem with the washer, it sent me to this site saying what they thought was the problem, I live chatted with someone and they confirmed the solution. I ordered the part and it came in 2 days and my husband fixed it. And now I have a working washer again. Thank you for your site. Anne

Although this was listed as 'a bit difficult' and talking a bit longer than normal, this was because the agitator cap had leaked, and over time the agitator bolt had become completely rusted such that a socket simply couldn't fit. Due to the tight confines, I also could not get a needle-nose vise-grip to hold on to the nut, so attempted to drill out the bolt. This ended up being a problem, but it turns out that drilling AROUND the edge of the bolt and through the edge of the plastic allowed me to remove the top of the agitator, which then allowed a normal pair of vise-grips to be used to remove the bolt. Once the bolt is removed, everything simply fell into place, and the overall job 'should' have only taken a couple of minutes and been 'really easy', except for that rusted-out bolt.

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]