MWFW8500SR02 Whirlpool Washer - Instructions

I watched the youtube video, then ordered the part from partselect. I then took my ipad out to the garage where I placed my washing machine and completed the removal of the old seal and installed the new one with ease. Be patient when you try and fit the new seal over the lip on the machines doorway. That was the only hard part. Once I got it started, the rest was easy. I am very happy the video was available and even easier to follow the link to order the part. Thanks! Presslerc

Removed top panel. Removed rear panel. Replaced belt. Fairly easy only issue was getting the actual belt pulled enough to wrap around the pulley.

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!

We purchased a new pump and installed it very easily. My washer works great!

First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

Replaced the pump assembly. The different type of clamp supplied in the kit was very helpful.

Had my appliance man do it. It was the first one he had ever done in 20 years of working on Whirlpool. It was quick. The parts I received from you were cheaper than his supplier. Needless to say that made me very happy!

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

I removed the three bottom screws and removed the plate. Removed the control panel, removed the star screw on the left side and pulled off the front panel of the machine. Loosen the bellow clamp with a phillips head and pull off the front spring clamp on the bellow. Pull off the old bellow and re installed the new one. Installed and tightened the bellow clamp and spring loaded clamp on the front of the bellow and re installed the panel, and control panel. Checked for leaks.

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

Just use the video. Shows you all you need to know. Very easy. Do it yourself and it saves you money.

I removed the service door and rear access panel to get at the bolts on the shocks and removed them one at a time. I did notice that the replacement shocks were heavier duty than the originals but was not an install problem. The machine is good as new now. A note, an appliance company wanted 800 to 1000dollars to diagnose and repair problem,i was able to do the repair myself for 70 dollars

I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!