GHW9200LW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- carlos from TAMPA, FL
- Parts Used:
- WP8181651
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original door hook broke in two pieces.
As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from WEST BABYLON, NY
- Parts Used:
- WP8181850
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water flooding from under the washer
Remive 3 screws along bottom front panel and remove that by pulling down and off. Remove 4 screws from the back of washer along the top to remove top cover. Pull out dispenser tray. Remove 2 screws from along dispenser, then carefully remove the control panel by inserting a screwdriver to release internal clips along the top. Put the control panel on top of the washer. This gives you access to 2 more screws at the top, and also 2 screws on the bottom, that will release the door panel. You'll have to disconnect 3 wire connections to get access to the wide rubber gasket (bellow). There is an inner ring and an outer ring holding it in place. The outer ring is a spring. Pull that off. Then remove the inner by loosening the screw holding the clamp. Pull the bellow off and replace with the new one. Make sure the gasket goes completely over the large water spout and the smaller button sprayer at the top taking caution to have the gasket sit between the two plastic washers attached to it. Make sure the belllow is firmly seated inside and out before attaching the bellow. Reattach everything in reverse order. Problems you'll run into: getting the spring on the outer gasket as it is tight to get on and the rubber will keep slipping off the edge where it is seated. Also, you may need an extra pair of hands to hold the door up while you attach those wire connections as there is no play in the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elwyn from NORWAY, ME
- Parts Used:
- WP8181694
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
water valve would not open all the time
First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEE from RIO RANCHO, NM
- Parts Used:
- WP8182634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer would not start.
easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from ATLANTA, GA
- Parts Used:
- WP8181850
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Tears in the bellow, leaking
Follow the video when you find the part. It's spot on, exactly what you see and can expect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Dothan, AL
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door handle had broken off
I removed the screws holding the fragment of the door, removed the door fragment then placed the screws in my new replacement door (that got here in record time - THANKS!), put it in place, fastened the 2 screws and the problem was solved!!! I am NOT a diyer so this was great for me!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Kenosha, WI
- Parts Used:
- WP8181694
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water backup when not in use, strip threads
Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.
Reverse order to install.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.
Reverse order to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Platte City, MO
- Parts Used:
- 8181877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced handle on frontload
Removed 2 torx head screws and replaced handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MANCHACA, TX
- Parts Used:
- WP8181846
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Handle
Two screws. Take off old handle. Put on new handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from LONG BEACH, CA
- Parts Used:
- WP8181846
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door handle was cracked and eventually broke off.
Ordered the part. When it came we needed to find the correct screwdriver because the screw did not work with philips head screwdriver. We used slotted even though it wasn't that type of screw. It worked just fine and installed very easily. It worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garey from LITTLETON, NH
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
Unscrew old one,screw on new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Fort Salonga,NY 11768, NY
- Parts Used:
- WP8181694
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
drum continuing to fill with water
Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CINDY from PASADENA, TX
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Handle Broke Off
I removed two screws and removed broken piece and replaced the handle with the same two screws. The color and match of the handle was perfect.
Was this instruction helpful to you?
Thank you for voting!