GHW9200LW0 Whirlpool Washer - Instructions

1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.

Unplugged power cord, turned off both water valves on the wall, Disconnected the water hoses o the back where they are attached to the water inlet valve. Note: there will likely be some water left in the hoses. Then removed top lid of washer (this is a front load washer) by removing the 3 nut screws on the back of the lid and sliding it to the back and lifting off.. Disconnected the small hose that is attached to the water inlet valve by squeezing the hose clamp and sliding the hose off. Removed the 4 wires connected to the water inlet valve (marked each one with a number in order) then removed the Phillips head screw on the back of the machine holding the water inlet valve, sliding the valve to the right, . Removed valve, and replaced with new one, and re-installed by reversing order of removal.

Followed internet instructions

Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

Easy to install.
Baffles came with 3 screws and no directions.
The screws unnecessary and we easily figured out how to install.
Quick delivery, 1-2 days.

First I removed the two screws that hold the door handle in place. I then pulled the door handle off and replaced it with the new one. As long as partselect.com is around I'll be able to keep my appliances longer.

Super easy replacement. 2 Screws and a regular screwdriver or a #20 torx will work.

firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.

We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.

The baffles do push thru slots in the drum and by then pulling them towards you, it moves slightly locking them into place. There are screws supplied and they could be installed to aid in the baffles not coming off as ofter but this cannot by done by the average person for you would need special tools and allot of fixet smarts and patience. My washer can be set at a higher spinout speed and this does save on drying costs but the trade off is the baffles break off way too often. There are metal tabs in the drum that are raised up and snap behind tabs on the underside of the baffles as you slid them towards you install them. If you rebend these tabs up with a longnose pliers twice as high as they are, they will have more holding force, keeping the baffles from coming off as often. In my opinion, the baffles should have been designed to slide backwards to lock them in place, not foward. If you look at how they are shaped, they natually have pressure pushing them towards the back of the drum in the spin cycle which just contributes to the problem of them coming off in the first place.

Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.

Just removed two screws with a phillips screwdriver and screwed the new handle on. Super simple

Simple repair. #20 Torx, pair of pliers and 10 minutes to complete the job. Part was exact fit. Turned off the water supply, removed the three screws at the back, slid the top to the back and lifted it off to reveal the valve. Removed the screw holding the valve in place, slid the valve to the right and pulled the valve out to the inside. Used pliers to move the hose retainer off the valve, removed the hose, unplugged the wires, and reversed the procedure to install the new valve.

Easily. 4 Screws. 2 Clamps.

This was truely easy. All I needed was a flat head screw driver and it was done within five minutes.