3MAS1432FW1 Whirlpool Washer - Instructions

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

Pulled up on fabric softener dispenser and removed it. Had to use pliers to remove cap and seal to get access to the bolt holding the agitator in.

Realized my socket extension wasn’t long enough so went to Lowe’s and bought another.

Was unable to hold the bottom of the agitator to keep it still and get enough leverage to remove the bolt. I poured hot water over it and then climbed into the washer and used my foot to hold the vanes still while I removed the bolt. Once I got the agitator out, the rest was a breeze. Separated the top of the agitator from the bottom by placing it on the floor, using my feet to hold it down and pulling up to remove the top part of the agitator.
Turned the top of the agitator upside down and removed the cam and feed dogs. Assembled the new one and held the agitator top horizontally while placing the new part back in.
Reassembled the top and bottom of the agitator and put it back into the washer. Tightened the bolt, replaced the cap with its seal and pressed the fabric softener dispenser back into place.

1. Remove Top Cap.
2. Remove Seal Cap.
3. Remove 7/16 Bolt
4. Lift out Old Agitator
5. Put in NEW Agitator
6. Replace 7/16 Bolt
7. Replace Seal Cap
8. Replace Top Cap.
9. Sit back and enjoy your clean clothes

I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.

Unplug electrical cord, disconnect water inlet hoses and drain line at rear panel. Move washer to garage or larger work area if necessary. Disconnect control panel from top of washer cabinet by removing the two screws at the front corners of the control panel. (The control panel can now be flipped up and back when you are ready to remove the cabinet assembly.) Disconnect the rear panel from cabinet assembly by removing attaching screws at bottom of rear panel (and along the vertical edges if any screws are installed there). Either slightly lift the rear panel up off of the two clip brackets that attach it to the rear top edge of the cabinet assembly, or if need be remove the clips from the cabinet slots. With the rear panel loose, slide the control panel assembly slightly towards the rear and up to disengage it from the cabinet slots, then tip it up and back, away from the cabinet. The cabinet assembly (with top attached) can now be tipped forward and away from washer to expose the internal workings. (It may be necessary to support the rear panel and/or control panel.) The water pump is attached to the front of the motor by two spring clips. Disconnect the two water lines from the pump, then remove the two spring clips. Pull the pump forward off of the shaft extending out of the motor. Install the new pump, then assemble the washer in reverse order. (I was unsure where the leak originated on my washer so I completely removed the rear panel which entailed disconnecting from it the electrical cord fitting, drain and input water fixtures and various other brackets. Pump replacement can be accomplished without completely removing the back panel.)

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

just like video showed really helpfull

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

First I removed the fabric softener dispenser. I removed the inner cap seal and agitator retaining bolt. Then I firmly pulled up on the agitator to remove the complete agitator assembly. I replaced the inner cap seal and installed the new agitator bolt with rubber washer. I placed the new agitator assembly on the drive shaft and tightened the bolt. Lastly I installed the inner seal and the fabric softener dispenser. The total time spent was around 10 minutes.

simple and easy . Just tipped the machine back, pump was right there in the front.
Hardest part was getting the old pump off the shaft. I used a small block of wood & a large screwdrive to pry it loose (gently).

After it came off I filed off some corroded spots on the shaft before slidding on the new one. then its slid on easy,
Snapped on the clips , clamped on the hoses, Done, Momma's Happy, I'am Happy

Ordering was easy, Shipping was fast.
I will use you again.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job