WFW9400SWA10 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donnie from King, NC
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Bellow was torn by clothing
Unplug washer. Open door. Look at the very bottom of the bellow and will see a spring that is connected to a small wire that runs around the bellow holding the outside on. Using a flat head screw driver insert it between the wire and bellow, pull down slighty. Grab the wire and gentley pull off. Now the outer part of the bellow will be free, pull it toward you, and off the water/soap despinser, then push it into the washer. Now look to the right side and you will see a screw head that is actully a big clamp ring around the bellow. This is the hardest part. Use a small rachet screw driver with a 7mm socket to lossen. Pull clamp off gently, you can now removwe the bellow. Put bellow back on in reverse. There will be a small tab on the bellow it goes to the top. Took about 2 hours.
Was this instruction helpful to you?
Thank you for voting!
Bellows stained
I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Union, NJ
- Parts Used:
- WP8183202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Securing arm broke.
I started by dismounting the door from the washer, then placed the door on a flat counter with a towel underneath to avoid scratching. I unscrewed all the bolts securing the the frame. Once the frame was removed, I dismounted the broken door hinge and secured the new one in reverse order. Just a little time and patience. Job completed with no mess!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from Nevada, OH
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The washer was sending an error code (F21) and it was getting worse about draining I tore it apart twice and decided to order a new pump through your website and it can quick and I installed it and it works perfectly now after a year of cleaning the filter and not getting anywhere
My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Columbus Grove, OH
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
F21 code
Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeremiah from royalton, MN
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Socket set
drain pump impellar busted
I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- amber from rochester, WA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
the pump went out on the washer
took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Durango, IA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Would not pump out water, F21 codes checked and cleared all hoses and trap before pump still no luck.
Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was packed full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Norman, OK
- Parts Used:
- WPW10110225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water flow problem resulting in f20 error code
Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Burlingame, CA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Pump noise Rattle and not draining water out/ error code
Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Lodi, CA
- Parts Used:
- WPW10110225
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
F/H error
I had replaced the flowmeter, but that didn't solve the problem, so I ordered the hot/cold solenoid fill part. Other than ONE screw that was unique -- the back retaining screws were nut driver screws, the one retaining screw was a torx which, of course, couldn't be seen unless you pulled the washer all the way out. Unscrewed that, unhooked the hose clamp with pliers and worried the hose off, removed the four electrical connections (which were TIGHT) and replaced the part. Turned on the water and was dismayed to get a d/l error code. After some colorful language learned from my drill sergeant 40 years ago, I realized that was "door lock" and closed the door tightly. Ran great and the Mrs. thinks I'm a hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Tower Hill, IL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
replace drain pump
The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Gardena, CA
- Parts Used:
- WP8183202
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not close, piece on the bottom of the hinge that pulled door in was broken.
Remove the two screws holding the hinge to the washer body. Lift up on the hinge to remove from the washer. Remove all the screws holding the inner door piece to the outer cover. Remove the old hinge, replace with the new one. Put the two door pieces back together and tighten the screws. Place hinge back in on the washer body and push down. Replace screw at top and bottom. Close door and start using.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Naples, FL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
My washer was not draining
It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Rock Hill, SC
- Parts Used:
- WPW10121596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Divider Broke
I just put the divider in the dispencer
Was this instruction helpful to you?
Thank you for voting!