Models > WFW9400SWA10 > Instructions

WFW9400SWA10 Whirlpool Washer - Instructions

Jump to:

All Instructions for the WFW9400SWA10
106 - 120 of 197
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
lou from stamford ct, CT
Parts Used:
WPW10110225
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
HF code durring cycle
Removed top of washer and replaced flow meter.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOSE from OZONE PARK, NY
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
The Bellow of my washer machine was broken
I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks
Was this instruction helpful to you?
Thank you for voting!
Customer:
Antonio from La Puente, CA
Parts Used:
WPW10730972
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
My washer would not drain, weird noises, etc.
This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.
Was this instruction helpful to you?
Thank you for voting!
Customer:
donald from Stanwood, WA
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set
torn bellow
repair was a cake-walk with the video there to help.Thanx
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from Spanish Fort, AL
Parts Used:
WPW10730972
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Wrench set
Washer wasn't draining and spin cycle not working
Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks
Was this instruction helpful to you?
Thank you for voting!
Customer:
Duane from New Richland, MN
Parts Used:
WPW10730972
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
It was making lots of noise. Halfway through the cycle it would not pump all the water out
First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from North Pole, AK
Parts Used:
WP8182210, WP8182119
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Bellow had a large hole in it, and was letting water drain out all over the floor.
It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the space you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tina from Denver, PA
Parts Used:
WPW10730972
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench set
needed to replace water pump
dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump
Was this instruction helpful to you?
Thank you for voting!
Customer:
FAYE from ZEBULON, GA
Parts Used:
WP8182119
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
hole in bellow
Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Hopewell, NJ
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Front Bellow Moldy
Followed video, slowly. Was easier then I expected. Everything fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from Lyndeborough, NH
Parts Used:
WPW10730972
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers
Whirlpool Front loader washining machine F21 error code
Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!
Was this instruction helpful to you?
Thank you for voting!
Customer:
EMMANUEL from CLINTON, MD
Parts Used:
WPW10253483
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Timer was not advanced due to door lock failure
Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.
Was this instruction helpful to you?
Thank you for voting!
Customer:
laveda from juneau, AK
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
hole in bellow
pulled the front and top of the machine off, pulled off the old bellow, ordered the new bellow, and put the new bellow on. we looked on youtube.com for a video on repairing the machine.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Winifred from Livonia, MI
Parts Used:
WP8182119
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set
Bellow had mold and mildew
Found it impossible to get the bellow off the machine. Removed the front spring. Even tried to but off the bellow. No luck. Called repairman. He had to take off the front panel, door panel, and the top of the machine before he could remove the back spring/clamps.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Murphy, NC
Parts Used:
WP8182119
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Socket set
Bellows were moldy and underneath had mold
We hired a local repairman and he even had trouble . I would not suggest anyone trying this installation on their own. It took the repair guy an hour to do and he struggled. Not an eary installation
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WFW9400SWA10
106 - 120 of 197