7MWTW1603AW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from HANCOCK, MD
- Parts Used:
- WPW10006384
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer wasn't spinning after rinsing but the motor was running
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from NAPLES, FL
- Parts Used:
- W10780048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
I followed the video guide, which was excellent
I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.
Machine works great now.
Machine works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernestine from CARRIERE, MS
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Making noise when spinning tub hit side of washer.
Remove top of washer suspension
Rod goes on side of tub .
Rod goes on side of tub .
Was this instruction helpful to you?
Thank you for voting!
Splines on lower agitator bad, worn.
Had to clean debris on metal drive shaft splines in orderv forvnew lower agiitator to seat properly. Install upper agitator and parts then reinsert bolt in upper agitator. Install cap and o-ring, fabric softner dispenser and test for proper operation.
Was this instruction helpful to you?
Thank you for voting!
When washer would go into spin cycle it would shake violently. This also prevented the spin cycle from completing leaving clothes soaked
Followed videos sent with the repair items. It was very easy and solved my issue. My washer did not have the centering springs to begin with so I was unsure if I even needed them. But after replacing all the suspension rods and adding the pack of centering springs this has solved my issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Edgewood, TX
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
top agitator would not operate
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from RAY CITY, GA
- Parts Used:
- WPW10072840, WP3363661, 80040, 285587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Would not agitate
Exactly as shown in your video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from HANCOCK, MD
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer wasn't spinning on final spin
First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NICHOLASVILLE, KY
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
The plastic teeth on the inside of the large agitator stripped out.
I needed an air impact wrench to remove the single nut. It was stuck on there. Once the Nut. Was removed it was an easy repair. Perfect fit! Just pop it on the shaft and replace the bolt. Since I had my air tools out already I gave it a couple of dugga duggas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BELMONT, MI
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Lid lock/latch stuck closed
Watched a video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Hyannis, MA
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top section of agitator would not spin.
Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Nashua, NH
- Parts Used:
- WPW10072840, WP3348752, 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Not spinning clothes at top of load
I removed dispenser for softener, then pulled cap inside upper agitator, I was able to get my fingers in the grips and pull firmly to unseat it. (disgard o-ring it comes with the repair kit). I then removed the bolt from center and grabbed the bottom of the lower agitator and gave it a good tug to release the whole unit. If that don't work you can get a flat tip screwdriver between the two sections and pry up slightly. Once it was all loose I removed the upper assembly taking care to to remember how all the pieces were assembled. replaced everything in the same order and when it came time to reinstall the inner cap and seal I made sure I put the cap in straight. Also if the seal doesn't cooperate you can use a little liquid soap to lubricate it. you dont want to use grease because it could possibly get on the clothes (the softener sits in there)! You can use the tip of the screwdriver to tuck the oring in if that doesn't work but be very careful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BAKER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
Was this instruction helpful to you?
Thank you for voting!
Washer was out of balance on spin cycle
I do not know much about washer repair and after watching how to replace the suspension rods I decided it was not as difficult as I thought. I replaced the suspension rods and springs and that fixed the problem. The price for parts was reasonable and I received my parts in 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chet from CLEARWATER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
heavy loads did not spin dry properly
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Was this instruction helpful to you?
Thank you for voting!