WTW5550XW3 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOHN from PUNTA GORDA, FL
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Will Not Tumber
I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Shawnee, KS
- Parts Used:
- 3406839
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
I had only seen a one piece rack .The 2 piece threw me for a loop.
I thought I had checked the arm piece of the rack real good for a product number on my original part but I missed the number till the 2nd box came in, and a looked real careful and realized it was the same as the order I thought was bad.
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margo from FOX ISLAND, WA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer was making bad noises like a bearing was going out, then it got worse and sounded really loud, so I couldn't even run it.
Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from PORT ALLEN, LA
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Belt
My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from CHEYENNE, WY
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Noisy, screeching, sounded like roller bearings were shot
Watched the video, followed the printed instructions for reminder when necessary. Needed a second person briefly to hold the dryer tub when installing the new belt, and also when removing/replacing the front panel. Beyond that, it was straight forward and relataively easy to do. Solved the noise problems and it dries more evenly now as well. The one thing the instructions don't say is to check the rear canvas seal when the tub is re-inserted into place to assure it doesn't fold back on itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVE from FULDA, MN
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
drum roller were worn out
flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from HARRISBURG, PA
- Parts Used:
- W10404050
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer would not agitate or spin and took over 2 hours to go through all cycles.
Started by replacing the lid latch assembly but this did not fix the problem. Parts Select representative suggested replacing the drive pulley clutch assembly. I order this and a new shift actuator. Had difficulty installing the new black shift actuator as it has a different electrical connection location from the original red part. The plug on the existing wiring harness would not reach the socket on the new black shift actuator. I had to remove the socket from the new black actuator casing so the plug would reach the socket. Washer is now working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from HUDSON, MI
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Drum wouldn't move. Belt Broken.
Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor. But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ace from VENICE, FL
- Parts Used:
- W10205824
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The spin cycle was very noisy & shook the whole machine.
The part we needed wasn’t pictured — nor the quantity identified. There are 4 absorbers required for full replacement. I received one absorber — 3 1/2 inches X 1 1/2 inch wide X 1/8 inch thick. Including shipping, the cost was $53.00!! Outrageous! A 10 foot roll of the same thing can be bought online for less than $20.00.
By the way, it didn’t solve the problem.
Paul
By the way, it didn’t solve the problem.
Paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from PHILADELPHIA, PA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dryer was making loud noises.
Pretty much followed your great video: . Watching it gave me the confidence that I could accomplish the job myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from JOHNSTON, RI
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
belt worn
replaced rollers, belt and pulley. Video was very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from MYRTLE BEACH, SC
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
noisy dryer
followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurel from GODFREY, IL
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Dryer was making a funny dragging noise
Followed the instructions on the video. I was completely impressed because all the pictures on the video matched what I was looking at on the dryer. Very good job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WARMINSTER, PA
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer would go into the cycle to rinse dry.
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Oneida, NY
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Sqeaking Belt Drum wouldn't turn
Unpluged Dryer
Removed the two screws by the lint screen
Lifted the top of the dryer up by using a putty knife to push in the locking clips that hold the top down
unhooked door wiring switch
Removed the front door panel
Removed drum
Shop vac the unit
replaced the worn parts
reassembled the unit
Removed the two screws by the lint screen
Lifted the top of the dryer up by using a putty knife to push in the locking clips that hold the top down
unhooked door wiring switch
Removed the front door panel
Removed drum
Shop vac the unit
replaced the worn parts
reassembled the unit
Was this instruction helpful to you?
Thank you for voting!