WTW4700YQ0 Whirlpool Washer - Instructions

W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.

I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machine worked fine right after I was done.The new part was identical the the old one,and the job was a snap.

I removed the softener cup, unscrewed the bolt and replaced the cam kit. Super easy just like everyone else said. Parts were here very quickly and at a great price!

First I pulled the liquid softener dispenser from the top of the agitator. Then I pulled (also by hand) the cover that was beneath it. That revealed the bolt holding the agitator in place. I loosened this with a socket set and removed it. The old Cam-Agit, which was stripped, popped out and the new one popped in. I then reassembled everything in reverse order and was done in approximately 5 minutes. The agitator works great now and we are no longer getting clumps of powder detergent in the clothes from lack of agitation.

Hi I took off the old one and put on the new one quick and easy

Found common diagnosis and instructions on internet. It is not difficult to replace.
Unfortunately, this new latch assembly did not fix the problem.

Please check the order was refused so I would not have to pay to ship back. The lady I spoke to on the phone said to do it this way. I have been TRYING to call for 2 weeks but no one is answering the phone due to CV19!!
The order is back at your warehouse. Please give me my refund!! Plus I have emailed your CS dept. numerous times with NO answer, only automated.

Removed the liquid softener cartridge.
Removed the plastic seal inside the upper agitator using a pliers.
Removed the bolt holding the agitator in place using a 7/16 socket wrench with a 6 inch extension.
Lifted the agitator out.
Separated the upper and lower agitator into two pieces.
Replaced the cam assembly inside the upper agitator.
Reversed the whole process.

Much like the other descriptions. I found the video helpful and this was the only vendor that had diagrams, so you could see how things went back together. When I popped off the top piece, everything went flying, as someone else mentioned, so the diagram was essential.

Per your directions. Note that part has been updated from original. Looks like an improvement, adds tab to grab rod, but changes installation.

Watch video on the site and the insulation will be easy and take about 30 min.

I bought the cog kit. Nice directions on how to assemble but their were no instruction on how to disassemble the agitator. I wound up replacing the whole agitator for $60 vs $6 for the parts I needed. The agitator had only one nut (which you had to take off to get at the cog assembly anyway. The agitator is the way to go. The cogs are halfway down the top part of agitator with no way the get them out without a special tool or ruining the bottom part of the agitator as the clips are part of the bottom piece. If you need special tools they should be listed. If you need to be a trained technician that should also be stated. To give you parts in the middle of an assembly with no instruction on how to put them in the assembly is plain wrong.

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

My husband just took the bolt in the middle took the broken one, put the new one, put the bolt back the lid the rubber seal and done. Working like new.
Basically we did what everyone else did with this part, it help me realize I did not need to call a repairman for this, I knew hubby would be able to do this.

Remove dispenser and barrier cap by hand to access cam assembly. Unbolted agitator assembly and pulled up firmly.
Able to access and replace cams. Before pulling out note how assembled and make sure to put back exactly the same. Singe person using this machine for 8 years. Poor design or quality of cams to fail so soon. Family of 5 would have been through this in a few years. For only 15 dollars definitely worthwhile repair. Parts arrived in days.