4GWTW4800YQ0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Amy from INMAN, SC
- Parts Used:
- WPW10238319
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door alignment
I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from BEECH ISLAND, SC
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Springs worn out on the suspension rods. (Noisy drum in spin cycles)
The video posted on this site will walk you right through the repair. Great service. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from FUQUAY VARINA, NC
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator doggs wore out
Followed youtube video. Great instruction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luu from STANTON, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
No problem
That OK , easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from KISSIMMEE, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer shaking and banging loudly during spin cycle
Replaced the suspension rods
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from PRAGUE, OK
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Agitator wouldn't agitate
Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WALTER R. from BEDFORD, TX
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
COGS WERE WORN OUT
THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie from DETROIT, MI
- Parts Used:
- 285809
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Upper agitator loose not agitating.
Followed installation video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shannon from HVRE DE GRACE, MD
- Parts Used:
- 285809
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
washer would not spin out
watched the video it was very helpful ~ repair went smooth ~ had to have a friend hold the tub in place while I broke the bolt loose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from KISSIMMEE, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Washer drum banging on spin cycle
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Was this instruction helpful to you?
Thank you for voting!
Upper agitator would not push clothes down as required for cleaning
I went on YouTube and seen how to do this job it showed it to be quite simple I then went on parts select.com put in my model serial number and was able to come up with a complete parts breakdown I then ordered the parts that I needed when they arrived I installed them the washer is working great thank you Parts select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from OXLY, MO
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Banging when in spin cycle.
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodger from ANDOVER, OH
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
top part ofagitator not turning.
Followed instructions on website video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Spring Grove, IL
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Agitator was free wheeling
repair was really simple. If you can get it apart, you can fix it. the parts fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from HAUGHTON, LA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
agitator stopped working
Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....
Was this instruction helpful to you?
Thank you for voting!