WTW4880AW1 Whirlpool Washer - Instructions

I removed the softener cup from the top of the agitator unit. The auger works separately from the bottom agitator. Remove the cap from down in the auger. There is a 7/16" bolt that holds the Auger and agitator to the center shaft. Loosen that bolt with a 7/16" socket on an extension from the ratchet wrench, and remove it from the bushing- I used a magnet. You will need to hold the agitator to loosen the bolt. Save that bolt. You will need it later. The entire agitator and auger can be lifted as a unit straight up out of the washer tub. There is a plastic bushing in the replacement kit. Slide it down over the center shaft with the small tabs up, then apply some Vaseline to the tabs as a lubricant. The new agitator can now be slipped down over the center shaft and seated on the bushing. Place the top auger onto the shaft down on to the agitator. Next, assemble the top bushing by placing the four cogs into the slots with the small pegs. The cogs must have the side with the raised area on the top of the assembly. Next push the plastic keeper down over the center of the bushing to hold the cogs in place and push it down to secure the cogs. Place this assembly into center shaft and line up the four rectangular holes in the top bushing with the four plastic prongs below. The top bushing assembly may be pushed down and secured by the four upright pegs below. If there are plastic tabs obstructing the rectangular holes in the top bushing , you can put the bolt back into the center hole and carefully tighten it down making sure the four holes align with the four pegs below. Tighten until the top bushing is securely in place. You will need to hold the lower agitator while you tighten the bolt with the socket wrench. Replace cap over the top bushing, then the softener cup into the top of the agitator assembly. The job is complete.

Watch video on the site and the insulation will be easy and take about 30 min.

Per your directions. Note that part has been updated from original. Looks like an improvement, adds tab to grab rod, but changes installation.

Much like the other descriptions. I found the video helpful and this was the only vendor that had diagrams, so you could see how things went back together. When I popped off the top piece, everything went flying, as someone else mentioned, so the diagram was essential.

I bought the cog kit. Nice directions on how to assemble but their were no instruction on how to disassemble the agitator. I wound up replacing the whole agitator for $60 vs $6 for the parts I needed. The agitator had only one nut (which you had to take off to get at the cog assembly anyway. The agitator is the way to go. The cogs are halfway down the top part of agitator with no way the get them out without a special tool or ruining the bottom part of the agitator as the clips are part of the bottom piece. If you need special tools they should be listed. If you need to be a trained technician that should also be stated. To give you parts in the middle of an assembly with no instruction on how to put them in the assembly is plain wrong.

used the Parts.com video. I am not mechanical at all, but removed the old part and installed the new part without a hitch. Very happy.

1. Removed the fabric softener dispenser

2. Removed Barrier Seal Cover

3. Removed bolt and seal

4. Removed and replaced CAM Agitator Assembly

5. Reversed the removal steps.

Followed the video

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!

We also purchased from this site the agitator repair kit! The youtube videos were extremely helpful!

My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.

Followed YouTube video

Excellent standard shipment time

Ordered the inlet assembly from this site. Received it the day after I received the notice it shipped. Watched their video of how to replace the part. Easy job, done in 15 minutes. Only needed a screwdriver to take the cover off the back of the washer control panel. A company wanted $400 to replace the part.
Definitely recommend the company and will use again.

Had to clean out area where bolt was to go as it was full of debris. Placed agitator on, bolted on , placed softener dispenser on. Done

Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.