7MWTW1502AW0 Whirlpool Washer - Instructions

I removed the softener cup from the top of the agitator unit. The auger works separately from the bottom agitator. Remove the cap from down in the auger. There is a 7/16" bolt that holds the Auger and agitator to the center shaft. Loosen that bolt with a 7/16" socket on an extension from the ratchet wrench, and remove it from the bushing- I used a magnet. You will need to hold the agitator to loosen the bolt. Save that bolt. You will need it later. The entire agitator and auger can be lifted as a unit straight up out of the washer tub. There is a plastic bushing in the replacement kit. Slide it down over the center shaft with the small tabs up, then apply some Vaseline to the tabs as a lubricant. The new agitator can now be slipped down over the center shaft and seated on the bushing. Place the top auger onto the shaft down on to the agitator. Next, assemble the top bushing by placing the four cogs into the slots with the small pegs. The cogs must have the side with the raised area on the top of the assembly. Next push the plastic keeper down over the center of the bushing to hold the cogs in place and push it down to secure the cogs. Place this assembly into center shaft and line up the four rectangular holes in the top bushing with the four plastic prongs below. The top bushing assembly may be pushed down and secured by the four upright pegs below. If there are plastic tabs obstructing the rectangular holes in the top bushing , you can put the bolt back into the center hole and carefully tighten it down making sure the four holes align with the four pegs below. Tighten until the top bushing is securely in place. You will need to hold the lower agitator while you tighten the bolt with the socket wrench. Replace cap over the top bushing, then the softener cup into the top of the agitator assembly. The job is complete.

took off the soap dispenser, removed the agitator using a 7/16" socket with an extension. replaced the old top agitator dogs and retaining ring with new ones, re-installed top agitator on bottom, thenput whole assembly back shaft, dropped in bold and tightened. whole experience was fast and simple. the parts came fast and where a perfect fit.

Followed the directions provided. Took less than 15 minutes and the washer works like new.

Remove softener dispencer, use flat tip screw driver to remove agitator cap, there is a slot, insert flat tip screw driver and pry up, once removed you will see the damaged dogs or cogs, use 3/8 drive ratchet with 10 or 12 inch extention and if memory serves me correct a 9/16 socket, loosen bolt and remove top agitator, there is a thrust washer between bottom and top agitator, it comes in the kit, use a little grease preferrably water resistant grease on top of washer, replace top agitator then the plastic device that the cog are inserted into and tighten bolt, put agitator cover back on with a gentle slap of the palm and reinstall softener dispencer, you are done and cloths will agitate properly again, fairly easy job and washer agitator works like new, great kit, would reccomend.

Per your directions. Note that part has been updated from original. Looks like an improvement, adds tab to grab rod, but changes installation.

Watch video on the site and the insulation will be easy and take about 30 min.

I bought the cog kit. Nice directions on how to assemble but their were no instruction on how to disassemble the agitator. I wound up replacing the whole agitator for $60 vs $6 for the parts I needed. The agitator had only one nut (which you had to take off to get at the cog assembly anyway. The agitator is the way to go. The cogs are halfway down the top part of agitator with no way the get them out without a special tool or ruining the bottom part of the agitator as the clips are part of the bottom piece. If you need special tools they should be listed. If you need to be a trained technician that should also be stated. To give you parts in the middle of an assembly with no instruction on how to put them in the assembly is plain wrong.

Watched the video. It was by far the easiest repair I've ever done. The washer is happy and stays in it place

Took ten minutes to pop upper assembly off and replace dogs. Note long ratchet or nut diver advisable 5/8.

I removed the cap over the ratchet mechanism, removed the ut holding the agitator in place, removed the agitator and cleaned all the parts. The assembly for the ratchet dogs was a 3 piece assembly that was included in the kit I bought from Part Select. I also bought a new cap and gasket since my old gasket had broken too. A new gasket was already included in the kit, so I didn't need ot buy the cap. I liked that th ekit included everything I needed and good instructions. parts got to me in about 3 days. Very happy with my Parts Select experience and the fact I saved at least $100.

First removed the cap, took out the screw, pulled out old agitator and replaced it with the new one

The old part popped right off, and new one installed. Works Great!!!

Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.

I already had the old agitator out, so when I got the new one I put it in the tub. You have to spin it a little so it seats properly. I then tightened the bolt with a 7/16” socket and my wife was washing a load within 15 minutes

Followed instructions.